Ford Fiesta Mk4 bucket seat guide
1995 to 2002, including the 1999 facelift and Zetec S
Four fitting routes are listed for this Fiesta: Sparco, OMP, Corbeau and RECARO. Send the build date and exact seat model so Garreth can choose the lower frame and Cameron can work through the runner and seat supports above it.
This guide covers the 1995 to 2002 Fiesta family, including the 1999 facelift and Zetec S enquiries. The facelift is also called Mk4.5. Some catalogues call it Mk5. Use the build date and vehicle type, such as JAS or JBS, to distinguish it from the 2002 to 2008 Fiesta covered by our separate guide.
The four kits have different side selections and seat requirements. The later facelift also needs its application checked against the supplied frame, because the catalogue date ranges are not identical. A seat that fits a Puma does not establish the complete Fiesta installation.
- Four listed fitting routes: Sparco 00499069, OMP HC793-2669, Corbeau FORDFIESTAMK4 and RECARO 86.60.26.
- Current Sparco and OMP side-option codes include the 00499069ST Top-Hat piece; check the package before adding another.
- RECARO 86.60.26 is physical right, offered here as RHD driver side. Its legacy application table gives December 1995 to April 2002.
- Corbeau general subframe kits are for compatible Corbeau base-mounted seats, with the exact Mk4 kit and side confirmed before ordering.
- Set the seat position before choosing the harness anchorage arrangement. Check cage body, door and roof requirements separately.
Mounting
The vehicle frame makes the lower connection to the car. A base-mounted seat needs the correct underside fixing pattern. A side-mounted shell needs compatible side supports. Add runners only where the complete assembly supports them, with the required fixings and usable locking travel.
Send Cameron the physical left or right side as well as whether the car is right-hand drive. The Sparco options use DX for right and SX for left. Keep each brand’s own code and selected shop option together when ordering.
Sparco 00499069 and the Top-Hat piece
The Sparco listing uses 00499069DX-00499069ST for the RHD driver side and 00499069SX-00499069ST for the RHD passenger side. Those are separate single-seat selections. The current package includes the 00499069ST Top-Hat piece. Itemise that package before buying extra fitting parts.
Our listing gives a 345 mm by 271 mm base interface and includes the 1999 to 2002 facelift. Sparco’s historic application table describes the JAS/JBS Fiesta from October 1995 to 1999. Garreth would check a facelift car’s exact application and supplied kit before treating that later coverage as confirmed for the order.
-
From £131.77 Incl. VATFrom £109.81 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
OMP HC793-2669
Our OMP listing offers HC793D-2669+00499069ST as RHD driver side and HC793S-2669+00499069ST as RHD passenger side, both including the Top-Hat reference. Confirm the actual supplied parts and handed frame before choosing a runner.
The shop attributes list 345 mm by 271 mm and 405 mm by 290 mm base patterns. Those measurements help identify a possible seat interface, but the complete seat and frame combination still needs checking. The Puma reference on the listing does not confirm every Fiesta body, seat or installation detail.
-
From £155.40 Incl. VATFrom £129.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Corbeau FORDFIESTAMK4
The Corbeau Mk4 listing has driver and passenger selections, with one frame ordered for each seat. Its FORDFIESTAMK4 reference is the shop identifier. Confirm the handed supplier code and package contents for your particular car before ordering.
Corbeau’s general subframe guidance covers its compatible base-mounted reclining and classic seats. It describes double-locking runners. Its current public application table does not identify this older Mk4 kit, so Cameron needs the actual Mk4 configuration confirmed. The general base kit is unsuitable for a side-mounted Pro Series or Sprint shell.
RECARO 86.60.26, physical right
RECARO’s legacy application table lists 86.60.26 on the right of the Fiesta for December 1995 to April 2002. Our product currently offers RHD driver side only. The left-hand 86.60.16 shown in that legacy table is not another selectable side on this listing.
The listing describes integrated sliding runners. Check the supplied assembly against the exact RECARO seat version before adding separate sliders or adaptors. The maker’s seat-specific application entries do not cover every RECARO base-mounted seat or competition shell.
Runners and the complete mounting assembly
The Sparco 0049306 and Endurance Motorsport kits below are runner options to check against the chosen seat and lower frame. For a side-mounted shell, the supports connect to the shell. The runner assembly sits beneath those supports where specified. Match both interfaces and the required hardware before ordering.
Cobra’s Premium runner has 291 mm and 405 mm handle-width options. Those widths are a separate specification from the seat’s full fixing pattern. A Cobra Monaco Pro has a stated 292 mm by 330 mm base pattern, so a 345 mm by 271 mm frame alone does not establish a direct base-mount connection.
Garreth checks which parts are already included in the order before adding runners. The RECARO listing describes an integrated arrangement, and the exact Corbeau package also needs checking. A second runner kit can add height and duplicate parts the assembly already has.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Separate side supports
The Sparco steel side supports are a separate option for a compatible shell. Confirm the shell’s side fixing points, support spacing and lower connection as a complete assembly. A support bracket’s product description does not establish approval of the whole installation.
Competition bucket seats
The OMP Champ-R, Sabelt GT3, Mirco RS2 3D, Sparco Rev QRT and Corbeau Pro Series X are side-mounted shell candidates whose widths and fixing details need checking against the chosen supports. Choose the seat around the driver, then check shoulder clearance and the installed position in the car.
The Cobra Monaco Pro is also a fixed shell, with base and side mounting listed. Its base pattern differs from the 345 mm by 271 mm pattern on the Sparco Fiesta frame. Keep it with the fixed-seat choices while Cameron checks the appropriate mounting route.
Garreth would compare the actual shell width and driving position before choosing between these seats. Sit in the chosen size if possible, then check the seat in the car with any helmet and cage you intend to use. The cards identify seats to assess, without promising cabin clearance from a catalogue description.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £425.40 Incl. VATFrom £354.50 Excl. VATPayPal Credit250+ coloursKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £732.00 Incl. VATFrom £610.00 Excl. VATPayPal CreditTop 10 productKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Reclining sport seats
The Sparco R100 is a base-mounted recliner. It has a stated 345 mm by 271 mm fixing pattern. It is a candidate for the matching Sparco or OMP base interface once the complete runner arrangement is confirmed. Check the backrest movement and clearance through the required adjustment range.
The Corbeau frame is a separate route for an appropriate Corbeau seat; a matching dimension on another brand does not change Corbeau’s application guidance. A RECARO seat needs its own seat-version check with 86.60.26. Tell Cameron if rear access is part of the brief so the selected mechanism and position can be assessed together.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Roll cages
Safety Devices specifies F044 for the three-door Fiesta Mk4/5 BE91, 1995 to 2002, without a sunroof. It describes a six-point bolt-in design and explicitly marks it as not for competition use. Check the selected front, rear and door-bar components with the car’s body and roof configuration.
-
From £858.00 Incl. VATFrom £715.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
The Custom Cages T45 kit below is listed here as FF3/94T for Mk3 and Mk4. The maker’s current page uses Mk3 in its main title while retaining Mk3/4 in image descriptions and the page address. Garreth would confirm the exact Mk4 body application, supplied design and certification requirements before ordering this weld-in kit.
Harnesses
Choose the harness after setting the seat position and establishing suitable anchorages. The TRS Clubman, Magnum, Takata Drift II and Drift III, and Schroth Profi 3×2 listings below cover different belt arrangements, so read the exact belt’s instructions for its seat requirements, strap routing, fastening method and attachment geometry.
A three-point harness does not establish that the Fiesta’s original belt points are suitable. A four- or six-point harness also needs its own installation checked. The number of straps alone cannot tell you whether a particular cage, harness bar or other engineered anchorage arrangement is appropriate.
Cameron checks the selected belt’s attachment requirements with the actual seat and car. A cage being present does not establish a suitable shoulder-belt attachment point, and a harness slot does not make every belt compatible. Treat the belt, seat and anchorage layout as one installation.
-
From £96.00 Incl. VATFrom £80.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £120.00 Incl. VATFrom £100.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £246.00 Incl. VATFrom £205.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £274.80 Incl. VATFrom £229.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £294.00 Incl. VATFrom £245.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £324.00 Incl. VATFrom £270.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £444.01 Incl. VATFrom £370.01 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
What fits
Use this table to compare the mounting routes and package checks. The exact seat, supplied hardware and car still need assessing together.
| Route or seat | Side or connection | Package detail | Check before ordering |
|---|---|---|---|
| Sparco 00499069 | Right DX / left SX, separate selections | 00499069ST included in current options | 345 x 271 mm base interface; confirm facelift application and runner package |
| OMP HC793-2669 | D option RHD driver / S option RHD passenger | 00499069ST in both current option codes | Shop lists 345 x 271 and 405 x 290 mm; check exact seat and assembly |
| Corbeau FORDFIESTAMK4 | Driver or passenger selection | Confirm handed Mk4 supplier kit and runner contents | Compatible Corbeau base-mounted seats; general kit excludes side-mounted shells |
| RECARO 86.60.26 | Physical right, RHD driver only here | Listing describes integrated runners | Legacy 12/1995 to 4/2002 application; exact seat version required |
| Side-mounted fixed shell | Supports connect to shell side fixings | Runner and lower support arrangement checked separately | OMP Champ-R, Sabelt GT3, Mirco RS2 3D, Rev QRT and Pro Series X are candidates |
| Cobra Monaco Pro | Base or side mounting listed | Base pattern 292 x 330 mm | Confirm intervening hardware with a 345 x 271 mm lower frame |
| Sparco R100 recliner | Base-mounted, 345 x 271 mm | Confirm frame and runner combination | Check full backrest movement and cabin clearance |
Application references: RECARO legacy base-frame table (2018 PDF), Corbeau subframe guidance, Safety Devices F044 specification and Custom Cages FF3/94T.
Common questions
Which Fiesta does this guide cover?
The 1995 to 2002 family, including the 1999 facelift often called Mk4.5 or Mk5. Confirm the build date and vehicle type with the supplied kit, because each fitting route has its own application range. Our separate Mk5 guide covers the 2002 to 2008 car.
Does a 1999 to 2002 facelift use the same kit?
Our Sparco listing includes the facelift, while the historic Sparco table gives October 1995 to 1999. Have the exact car and supplied frame checked before ordering. The guide does not extend every kit to every later car.
Which Sparco side should I select?
The current RHD driver option is 00499069DX-00499069ST, physical right. The RHD passenger option is 00499069SX-00499069ST, physical left. Select each required side separately.
Do I need to buy the Sparco Top-Hat separately?
The current Sparco side-option codes include 00499069ST, which the listing says is included, and both OMP option codes also contain that reference. Confirm the itemised package before adding another Top-Hat piece.
Does the OMP Puma reference prove a seat fits my Fiesta?
It does not establish the full installation. Match the Fiesta application and handed frame, then check the exact seat, runner and support interfaces. A shared reference cannot answer cabin clearance or package-content questions.
What is different about the RECARO option?
The listed 86.60.26 is physical right and offered as RHD driver side, with a legacy application range of December 1995 to April 2002. Confirm the exact RECARO seat version and supplied runner assembly.
Can I select a passenger-side RECARO frame here?
The current listing offers RHD driver side only. The legacy maker table identifies 86.60.16 on the left, but that is not a selectable passenger option on this product. Ask about a separately confirmed supply route for that side.
Will the Corbeau base frame carry a Pro Series shell?
Corbeau general base-frame kits are for compatible base-mounted reclining and classic seats. A side-mounted Pro Series or Sprint shell needs an appropriate support and lower mounting arrangement. Confirm that complete arrangement separately.
Are sliding runners included with every frame?
Check the exact package. The RECARO listing describes integrated runners and Corbeau describes runners in its general kit guidance. Confirm the older Mk4 Corbeau package and each Sparco or OMP assembly before adding separate sliders.
Does the Cobra Monaco Pro use the Sparco base pattern?
The Monaco Pro lists a 292 mm by 330 mm base pattern and side mounting, while the Sparco Fiesta frame gives 345 mm by 271 mm. Those different base patterns need the correct intervening arrangement.
Is the R100 a fixed bucket seat?
The R100 is a reclining sport seat with base fixings. The Monaco Pro and the other shells in the fixed-seat section have fixed backrests. Choose the mounting arrangement for the actual seat model.
Is the Safety Devices F044 suitable for competition?
Safety Devices marks F044 as not for competition use and specifies a three-door Mk4/5 BE91 without a sunroof. Match the exact body and selected components before ordering.
Can I use the original belt points for a harness?
That needs checking against the exact harness instructions and the actual anchorage layout. Strap count alone does not confirm suitable locations or geometry. Set the seat position before deciding the harness installation.
How many fitting frames should I order?
Order the required frame for each seat position. The OMP and Sparco listings have separate handed selections, and Corbeau has driver and passenger choices. The current RECARO listing provides only the right-hand RHD driver option.
More help
Send Garreth the Fiesta’s build date and type, door count, steering side and the seat model you want to fit, including the existing frame code if you already have hardware. Cameron can then check the supplied parts, physical side and runner arrangement with you.
For help with your Fiesta seat and fitting kit, call 0115 647 8650.
Need a personal recommendation?
We're here to ensure you pick the right seat.
Contact us today.















