Gift box
4WD Mini RC Drift Car - BMW
GSM Performance Customer Car Colouring Book Edition 1The Fiat Bravo HGT has a 2.0L 20V engine producing around 150bhp in a body under 1,200kg. The chassis is well-sorted for a car of its era, the steering is quick and reasonably communicative, and in the right trim a Bravo is genuinely entertaining on a circuit or a fast B-road. What the factory seats do not do is match that capability. They were adequate when the car was new in the late 1990s; after 25 years the bolsters have often given up, and even when fresh they left the driver sliding around under hard cornering.
A reclining sport seat sorts both problems without making the car awkward to use every day. You keep the fore-aft adjustment and the tilting backrest for passengers, and you gain the side support the standard seats never quite managed. Two direct-fit subframes exist for the Bravo: one from Cobra, one from Sparco. Which one you buy pins the seats you can run.
We stock a direct-fit subframe for the Bravo from two brands. A subframe bolts to the factory floor in place of the standard seat runners and sets the final seat height, and the brand of subframe determines which seats can go on it. That decision comes before the seat choice. Both bolt to the Bravo’s factory mounting points without drilling on a standard floor.
£231.66 inc VAT per side, sold individually (one seat position). Pairs with 291mm runners and takes the Daytona, the Misano and the Corbeaus. Tell us which seat you are fitting when you order.
£87.00 inc VAT per side, RHD driver and passenger listed separately. Listed for the Bravo from August 1995 to August 2001. Pairs with 345mm runners and takes the R100, the R500 and the Corbeaus.
Reclining seats bolt down through a base mount pattern, and on the Bravo two of them matter. Cobra recliners use 291mm x 330mm, which matches the Cobra subframe. Sparco recliners use 345mm x 271mm, which matches the Sparco subframe. The two patterns do not cross over, so a Cobra seat will not go on a Sparco subframe and a Sparco seat will not go on a Cobra one. Corbeau drill their recliners for both, which is why the SVR and RRS appear in both columns below and are the only seats here that fit either frame without adaptation.
| Seat | Bolt pattern | Cobra subframe | Sparco subframe |
|---|---|---|---|
| Sparco R100 | 345 x 271 | No | Fits |
| Sparco R500 | 345 x 271 | No | Fits |
| Cobra Daytona | 291 x 330 | Fits | No |
| Corbeau SVR / RRS | Both | Fits | Fits |
| Cobra Misano | 291 x 330 | Fits | No |
The R100 is the recliner we sell more of than anything else across the range. On the Bravo it works well because it is a compact seat in a compact car: the open base does not fight you getting in through the three-door aperture, and the fore-aft range from the runners is easy to live with. Sparco rate it for all waist sizes and for drivers both over and under six foot, which matches what we see on the counter. Very few people cannot find a comfortable position. Take it on the Sparco subframe with the runner kit and you have a complete driver-side upgrade for well under £500.
The R500 sits above the R100 in Sparco’s recliner range and the difference is at the shoulders and upper back. The backrest is taller, the shoulder support wraps further, and dual density foam in the base and backrest holds its shape better over longer stints at a circuit. It comes in fabric or Sparco’s Sky vinyl, which is worth choosing if the car sees wet track days and the seat needs wiping down afterwards. Both seat options share the 345mm pattern, so switching between the R100 and R500 later does not mean touching the subframe at all.
The Daytona is Cobra’s entry point into their reclining range and the one Cameron points most Cobra enquiries at, because the bolstering is a genuine step up from either Sparco without the price going past £700 on the standard build. The shoulder and thigh sections hold you through corners instead of letting you perch on them, and the build-to-order Signature system means the trim is your choice: spacer fabric, vinyl or leather, one or two colours, contrast stitching, and optional heating or lumbar if you want them. The Tartan Edition is available off the shelf for the considered look without waiting. Fits the Cobra subframe with 291mm sliding runners, self-contained for one side of the car.
Corbeau’s two most popular recliners share the same base and differ at the backrest. The SVR has a taller, smoother modern back; the RRS has the classic sculpted shape that most people picture when they think of a reclining sport seat. Because both are drilled for 291mm and 345mm, they are the only seats in this guide that fit either the Cobra or the Sparco subframe on the Bravo without any adaptation. Both are sold as pairs, which is how most people buy them: one order, both sides of the car sorted. The RRS also comes in a Low Base version for cars where headroom is tight, so ask about that one if it applies to yours.
The Misano is Cobra’s flagship recliner and the seat people stop at longest when they visit the showroom. It comes as the Lux and the Anniversary builds, both through the Signature trim system, and despite being the largest seat here it is also the lightest of the Cobras at 11.5kg against the Daytona’s 13.5kg. The bolsters are deep but the cushioning is where the money went: the base and backrest foam is noticeably different from everything else in this guide and it is the thing people comment on first when they sit down. Goes on the Cobra subframe with 291mm runners, the same route as the Daytona, so if you are considering both it is worth knowing the frame cost is shared.
Both subframes bolt to the Bravo’s factory seat mounting points, so there is no drilling on a standard floor. Between subframe and seat go the sliding runners, and they follow the same 291mm or 345mm logic as the frames. Both subframes are sold per side with RHD driver and passenger listed separately, so a pair means two in the basket. Torque the floor bolts properly before the first drive and check seat belt buckle clearance, because a sport seat typically moves the buckle somewhere new. One note on Corbeau runners: the millimetre figure in their product listing is the handle width, not the bolt pattern. The right option for the SVR and RRS is the Retro/Sportline handle width.
| Your seat | Runners to order | Works on |
|---|---|---|
| Sparco R100 or R500 | 2 Sparco Seat Sliding Runner Kit, £78.00 inc VAT a pair | Sparco subframe |
| Cobra Daytona or Misano | 2 Cobra 291 Seat Sliding Runners, £117.60 inc VAT a pair | Cobra subframe |
| Corbeau SVR or RRS via Sparco route | 2 Corbeau 345mm Seat Sliding Runners, £117.60 inc VAT a pair | Sparco subframe |
| Corbeau SVR or RRS via Cobra route | 2 Corbeau 291mm Seat Sliding Runners, £117.60 inc VAT a pair | Cobra subframe |
| Seat | Bolt pattern | Waist | Height | Weight | Price inc VAT |
|---|---|---|---|---|---|
| Sparco R100 | 345 x 271 | All sizes | Over and under 6ft | Not published | From £282 |
| Sparco R500 | 345 x 271 | 32 to 38in | All heights | Not published | From £329 |
| Cobra Daytona | 291 x 330 | 32 to 38in | All heights | 13.5kg | From £599.00 |
| Corbeau SVR / RRS | Both | 32 to 38in | All heights | Not published | From £984.00 a pair |
| Cobra Misano | 291 x 330 | 32 to 38in | All heights | 11.5kg | From £1,549.00 |
Prices include VAT and were correct on 18 August 2026. Where a weight says not published, the manufacturer does not give one and we will not guess it. Waist and height figures are the manufacturers’ published fitment ranges; if you are on a boundary, ask before ordering.
No. Both subframes bolt to the factory seat mounting points on a standard Bravo floor. Torque the floor bolts properly and check seat belt buckle clearance before driving, because a sport seat typically moves the buckle to a new position.
No. Cobra recliners use 291mm x 330mm and Sparco recliners use 345mm x 271mm, and the two do not line up. The Corbeau SVR and RRS are the exception, drilled for both patterns and compatible with either subframe on the Bravo.
The Sparco subframe is listed for the Fiat Bravo from August 1995 to August 2001. If your car is outside that window, check with us before ordering. The Cobra subframe listing does not carry a year restriction in its current listing, but if you are at a production boundary it is worth confirming the build date before committing.
Both manufacturers price the subframe as a single unit covering one seat position. Driver and passenger sides are listed separately for the Sparco subframe. The Cobra subframe is listed as a single unit and we need to know which seat position it is going to when you order. A pair of seats means two subframes in the basket.
If the car spends most of its time on track, yes. A fixed back saves weight compared to a recliner and holds you harder in the corners. A recliner wins when the Bravo is still a daily driver or carries passengers regularly, because the tilting backrest and fore-aft adjustment stay available. If you are weighing both options, get in touch and we can go through the seat and frame choices for this car.
If it were my money and the Bravo is a car I drive daily but also take on track evenings: the R100 on the Sparco subframe. It does most of the job for the least outlay, the frame comes off the shelf, and nothing about the combination needs revisiting later. If the car does more track than road I would move to the Daytona on the Cobra subframe, because the bolstering difference is real and the Signature trim means the interior can still look considered in a car I care about. The Corbeau SVR or RRS if I wanted both sides done in one order and did not want to lock into one bolt pattern before settling on a subframe. The Misano on the Cobra subframe if budget is not the constraint, because nobody who has sat in one ever argues it was the wrong call.
If you are between two of these seats, or anywhere near a waist or height boundary, call us on 0115 9893488 before you order. Cameron works through exactly this kind of fitment combination most days and would rather sort it before the seat ships than after.
Every Safety Devices roll cage we hold for the Proton Satria and Sport Coupe, and the design option on the Satria cage that decides whether it is competition legal.
The seat decides how many harness points you can run, not the harness. How to read the compatibility line on a seat listing, why a four point compatible seat will never take a six, and how to get the pair right first time.
The five reclining sport seats we recommend for the Volkswagen Golf Mk5 R32, built around the Cobra direct-fit subframe that bolts to the factory mounting points. Runner included in the frame price.
Bucket seat sizing answered with two numbers: your jeans waist and your height. The waist bands on every listing explained, internal against external width untangled, and real in-stock picks for slim, standard, wide and tall drivers.
James wants a retro look and the SRT logo in his 2012 Challenger SRT. The Planted bracket makes almost any recliner possible, so here is the ladder: budget, middle and top end reclining seats including the Sparco SPR and SPX, and the honest answer on getting a logo onto them.
Our number plate checker is live. Type your registration and see the seat brackets, subframes and rails that fit your car, with prices.
