Honda Civic EG bucket seat guide
Fifth-generation Civic: choose the kit for your exact car
A Civic EG seat conversion can use a vehicle-specific base, an adjustable side-mount kit or a BRIDE rail matched to a particular seat. Those routes include different hardware. Start with the car’s chassis code and physical seating side, then choose the upper fittings around the seat you want.
This guide brings together our fifth-generation Civic fitting listings, competition buckets, recliners and an EG6 cage option. Check the original model, body and market as well as the registration year. Planted lists the 1992-1995 Civic; BRIDE’s Japanese-market EG6 application begins in September 1991. A later registration or an engine swap does not establish the floor application.
The letters EJ also occur on later Civics. Use the full chassis code and generation when ordering, especially for a coupe or an imported car. The separate Civic EK guide covers the following family.
- Vehicle-specific options on this page include Sparco, Corbeau, Planted, M2, two PCI arrangements, SW and seven BRIDE rail types.
- Order the physical left or right assembly for the exact floor. A manufacturer's driver-side label may refer to a different steering layout.
- PCI's sliding kit includes its slider and side supports. Its adjustable fixed kit uses installation adjustments. BRIDE FX is also fixed; the other listed BRIDE types provide sliding adjustment.
- Planted and SW bases need the upper hardware specified for the seat. The Corbeau listing requires both a seating-side choice and a slide/tilt mechanism choice.
- Seat approval, runner acceptance and the vehicle installation must all meet the intended event's requirements. A product card does not confirm the completed installation.
Mounting
Check the original seat fixing points before ordering. Corrosion, previous welding or altered seat brackets can change what a replacement assembly needs. Give us photographs of any existing modification and the intended seat model.
A base-mounted seat attaches underneath. A side-mounted shell fixes through brackets alongside the seat, and those brackets need to suit its inserts, bolt size and mounting instructions. Where separate sliders are used with side mounts, the sliders sit below the side mounts. Measure the assembled seat position with the intended driver, footwear and helmet if applicable.
Sparco and Corbeau
The Sparco EG fitting-frame listing, product 16963, specifies a 345 × 271 mm base interface. Choose the correct handed frame and confirm the seat-side runner arrangement. A 345 mm width alone does not prove the fore-and-aft holes or the assembled height match.
The Corbeau EG/EJ listing, product 14612, is the dedicated route to discuss for a Corbeau base-mounted or reclining seat. It has required choices for seating side and a sliding or tilting subframe. Confirm the actual seat and supplied mechanism together; a tilting mechanism does not turn a fixed-back shell into a reclining seat.
Corbeau’s Sprint X is a side-mounted competition shell. Its maker specifies Pro-Team side mounts and M10 12.9 fixings. Have the complete vehicle-base and side-support arrangement confirmed before choosing it for a kit designed around another support system.
Planted SB041
Planted’s SB041 application is the Honda Civic 1992-1995. The maker identifies SB041DR as physical left and SB041PA as physical right. Our shop labels SB041DR as RHD passenger and SB041PA as RHD driver. Use the physical side and SKU together.
Planted’s general application guidance defaults to US left-hand-drive cars unless stated otherwise. That baseline needs checking against a UK or other-market floor; changing the driver/passenger label does not verify an international application.
The maker offers Standard and Alternate upper patterns. Standard includes the RECARO slider pattern; Alternate substitutes the Cobra/Scheel-Mann arrangement. The shop’s SB041 selection is by side, so confirm the supplied upper pattern and the exact slider before ordering. The lower base alone does not supply a seat or a complete sliding assembly.
M2: side-mount kit, base option and paired listing
M2 lists the EG/DC2 side-mount rail as M2-20268-S000 for physical left and M2-20268-S010 for physical right. The maker describes 290 mm side-hole spacing and sliding rails. That measurement still needs to match the exact seat shell, width, inserts and supplied supports.
Our single-kit listing, 16660, has side-mount and base-mount choices for each RHD side. The maker’s standard rail is a side-mount product. For a base-mounted seat, specify the base option with us and confirm the adapter supplied; the separate M2 adaptation bars, 19431, are accessories for a compatible M2 frame. Avoid buying another adapter until the selected package’s contents are clear.
The paired M2 listing, 260085, is also available. Confirm the left/right contents and mounting specification when ordering both seats. A pair of vehicle frames still needs seats and the appropriate seat-side fittings.
M2’s catalogue labels the application “Civic 92-96 EG & DC2” and lists EG3/4/5/6/8/9, EH9 and EJ1/2. Treat that as the manufacturer’s stated application and verify the actual chassis. It does not extend an EG kit to every Civic registered in 1996.
PCI: slider kit or fixed adjustable kit
PCI’s sliding EG mount, 19525, is the route for fore-and-aft movement after installation. The manufacturer lists SM-EG-L-S1 and SM-EG-R-S1 for the 1992-1995 Civic and specifies its S1 side supports with the standard slider kit. There is no reason to add a separate universal runner to that assembly.
The adjustable fixed mount, 190177, is the alternative when the position will be set using its fitting adjustments. PCI lists SM-EG-L-A1 and SM-EG-R-A1 and specifies A1 side supports for that kit. The available adjustment and the support arrangement differ from the sliding version.
Give us the seat model and measured shell width before choosing either one. Included side supports still need approval for the seat’s mounting system; their presence does not establish compatibility with every bucket. Check any proposed harness attachment against PCI’s instructions and the harness maker’s requirements separately.
SW lower bases
The SW EG listing, 269320, offers a lower base for each RHD seating side. It names SW-SM-0103 for the driver/right side and SW-SM-0104 for passenger/left. Side mounts, sliders and the relevant bolts are separate parts or optional additions.
Specify the full upper assembly and bolt size with the seat. The listing’s “345 mm wide” description does not give a complete two-dimensional seat fixing pattern. Check the actual car and base before treating an optional harness eyebolt or backing plate as an approved anchorage.
BRIDE rails for the front-wheel-drive EG6
The BRIDE listings on this page are for EG6 SiR/SiR II/SiR-S applications. BRIDE’s current matching data is principally for cars sold in Japan and marks this EG6 application as front-wheel drive. Confirm a different body, chassis or market separately.
Each type is available as H033 on the physical right and H034 on the physical left. On an RHD car those correspond to driver and passenger respectively. Choose the complete suffix as well as the side; it identifies the seat interface.
| Type | Seat interface | Main distinction |
|---|---|---|
| FG, 252551 | Side mount; 290 ± 5 mm longitudinal × 395 mm across | Sliding rail for seats within BRIDE’s specified fit list and dimensions. |
| IG, 252678 | Side mount; 290 ± 5 × 395 mm | Sliding type with aluminium side stays. |
| FX, 252623 | Side mount; 290 ± 5 × 395 mm | Fixed competition type. Event and seat acceptance still require checking. |
| XL, 252845 | Side mount; 290 ± 5 × 430 mm | Wider interface for the exact XL/wide seat applications in BRIDE’s list. |
| MO, 252725 | Bottom mount; 330 × 290 or 271 × 345 mm | For its named bottom-mounted seat families. |
| RO, 252784 | Bottom mount; 260 × 405 mm | For its named seat families and required interfaces. |
| XR, 252898 | Bottom mount; 260 × 405 mm | The STRADIA II type-XL application; the same nominal hole rectangle as RO does not make their seat applications identical. |
BRIDE publishes a separate compatible-seat list for each type. Its generic list and exact-car matching result must agree for the intended seat. Check the current seat revision and any required import side stays; do not choose solely from the brand name or a claimed drop in height.
Runners and adaptation hardware
The separate Sparco 0049306 runner kit, product 14036, is listed around a 345 × 271 mm base interface and is sold for one seat. Confirm both its seat-side and base-side interfaces, assembled height and adjustment clearance. A seat’s FIA label does not approve an unrelated runner installation for an event.
The Endurance runner, 21512, is another separate sliding option to discuss once the frame and seat are known. Its current listing does not provide a complete engineering drawing establishing every fixing centre. A 290 mm side-hole pitch on a bucket does not establish the bottom pattern of its side supports or runner.
Use the M2 bars only with the compatible M2 system and the exact base-mounted seat. PCI and BRIDE assemblies should follow their own instructions and supplied interfaces. Keeping each complete kit identifiable makes a later fitting check much easier.
-
From £87.00 Incl. VATFrom £72.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £222.60 Incl. VATFrom £185.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £166.20 Incl. VATFrom £138.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £330.00 Incl. VATFrom £275.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £134.89 Incl. VATFrom £112.41 Excl. VATPayPal CreditJust inSelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditJust inSelect options This product has multiple variants. The options may be chosen on the product page
-
From £276.00 Incl. VATFrom £230.00 Excl. VATPayPal CreditJust inSelect options This product has multiple variants. The options may be chosen on the product page
-
From £276.00 Incl. VATFrom £230.00 Excl. VATPayPal CreditJust inSelect options This product has multiple variants. The options may be chosen on the product page
-
From £294.00 Incl. VATFrom £245.00 Excl. VATPayPal CreditJust inSelect options This product has multiple variants. The options may be chosen on the product page
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditJust inSelect options This product has multiple variants. The options may be chosen on the product page
-
From £240.00 Incl. VATFrom £200.00 Excl. VATPayPal CreditJust inSelect options This product has multiple variants. The options may be chosen on the product page
-
From £264.00 Incl. VATFrom £220.00 Excl. VATPayPal CreditJust inSelect options This product has multiple variants. The options may be chosen on the product page
Competition bucket seats
The Sparco Sprint, OMP TRS-E and Cobra Monaco Pro offer base and side mounting routes. Their bottom fixings differ: the current TRS-E listing gives 345 × 270 mm, the Sprint gives 345 × 271 mm, and the Monaco Pro gives 292 × 330 mm. Use the exact drawing and support system for each seat; keep the different fixing centres distinct.
The OMP Champ-R and First R, Mirco GT 3D and RS2 3D, Sparco Rev QRT and Grid Q, and Corbeau Sprint X System 3 are side-mounted choices. Compare the shell’s shoulder width and the support’s total width against the door, tunnel and available adjustment.
All ten current listings identify FIA 8855-1999 approval. Check the exact supplied seat’s label and permitted use date with your event requirements. “System 3” describes the Corbeau shell construction; it is not a separate FIA standard. Corbeau’s own Sprint X guidance specifies the side supports and fixings required for its installation.
Try the seat if possible, especially where head-support wings may limit visibility or entry. A steel or composite construction description alone does not establish a safer choice for contact or an occupant’s fit.
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £388.80 Incl. VATFrom £324.00 Excl. VATPayPal Credit250+ coloursKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £425.40 Incl. VATFrom £354.50 Excl. VATPayPal Credit250+ coloursKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £810.00 Incl. VATFrom £675.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
💬
Competition seats for the Civic EGChoosing a bucket for the Civic EG
Start by trying the seat and measuring its shell. The Sprint, TRS-E and Monaco Pro have base and side mounting routes; each needs its own exact interface checked. For a side-mounted shell, specify the prescribed supports and complete Civic kit together.
Reclining sport seats
The Auto Style BS5, JW and MS listings include sliders and specify a 345 × 280 mm base pattern. Check the supplied slider’s lower interface against the Civic frame. Budgeting for another generic runner automatically can add hardware without solving that mismatch.
The Sparco R100 Martini, R333 and R500 Fabric/Sky listings use a 345 × 271 mm base interface and are seats only. Confirm a complete frame-and-runner arrangement and check that the recline controls remain accessible beside the tunnel and door.
OMP’s RTS listing specifies 345 × 270 mm base fixing. The Cobra Misano Anniversary and Spec 2 listings specify 291 × 330 mm and require attention to the ordered base specification; the alternative base choices are not interchangeable Civic floor frames. Specify the standard or other intended seat base before matching its hardware.
These recliners are separate from the FIA competition buckets above. A “Road & Track” shop category does not establish FIA homologation, legal acceptance or suitability for a particular event. Confirm standard-belt routing, buckle position and rear access with the actual seat in the car.
-
From £283.92 Incl. VATFrom £236.60 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £449.47 Incl. VATFrom £374.56 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £461.00 Incl. VATFrom £384.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
💬
Reclining seats for the Civic EGChoosing a recliner for the Civic EG
The Auto Style options include sliders on a 345 x 280 mm interface. The named Sparco recliners are seats only at 345 x 271 mm. Choose the seat and complete upper fittings together, then check access to the recline controls in the car.
Roll cages
The live Custom Cages listing, 18914, is the HO/98T EG6 International Multipoint T45 weld-in kit. It matches the manufacturer’s named EG6 application. Have the exact shell and intended event checked with the cage specification before ordering.
The maker describes an FIA-certificated kit and supplies installation and certification documents. The completed cage needs to follow that process. A certificated kit name does not prove a particular installation or make it suitable for every fifth-generation Civic body.
Plan the seat, door bars, access, padding and restraint anchors together. A cage tube is not automatically a harness attachment. Ask for the installation information and proposed shoulder-belt mounting provision before deciding the seat position.
Harnesses
Choose the anchors with the seat and harnessFollow the exact harness maker's routing and fitting instructions. Check the vehicle anchorages and event requirements before choosing a bar or cage provision.
Choose the harness as part of the seat and anchorage installation. Point count alone does not decide whether a cage is required or whether existing anchorages are suitable. The harness maker’s routing, end fittings, seat openings and approved use all need to match the completed car.
The TRS Clubman 3-point bolt-in, 14211, and Clubman 4-point clip-in, 14212, are different layouts. The three-point uses a combined rear shoulder attachment; the four-point uses separate rear attachments. A four-point designation does not include a crotch strap. TRS’s road instructions describe specified factory-belt anchor locations and require suitable loading and alignment; have those checked on the actual car.
The Clubman products and Magnum four-point listing are marked as unsuitable for HANS use. The TRS Magnum 4-point, 14217, is listed to FIA 8854-1998. The Magnum 6-point Superlite, 17148, is listed to FIA 8853-2016 and needs the appropriate anti-submarine strap routing and anchorages. Check the exact label, required event standard and FHR requirements.
Takata Drift II, 17344, and Drift III, 17348, are both four-point products in these listings. Their shoulder strap widths differ. Neither should be presented as the six-point competition alternative, and the listings mark both as unsuitable for HANS use.
The Schroth Profi 3×2, 19736, is a six-point racing harness listed to FIA 8853-2016. Follow Schroth’s competition instructions for the exact model and end fittings. Its racing application must not be described as a general road restraint; confirm the exact variant and permitted use.
For a shared road and track car, discuss how the original three-point belt, buckle and any sensors will be retained and routed. Avoid attaching belts to a seat bracket merely because a hole or an optional eyebolt is present. Ask the installer to verify the complete anchorage design.
-
From £96.00 Incl. VATFrom £80.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £120.00 Incl. VATFrom £100.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £246.00 Incl. VATFrom £205.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £274.80 Incl. VATFrom £229.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £294.00 Incl. VATFrom £245.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £324.00 Incl. VATFrom £270.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £444.01 Incl. VATFrom £370.01 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
What fits
Match the exact seat and supplied fixing system to the Civic kit. A listed approval concerns the product; the completed installation and the actual label must meet the intended use and event requirements.
| Seat | Mounting | Current listed approval | What to specify |
|---|---|---|---|
| Competition bucket seats | |||
| Sparco Sprint FIA Motorsport Bucket Seat | Base Mount, Side mount | FIA 8855-1999 | Seat only; 345 x 271 mm base or the specified side supports. |
| OMP TRS-E Velour FIA Motorsport Seat | Base Mount, Side mount | FIA 8855-1999 | 345 x 270 mm base listed; verify exact drawing and chosen supports. |
| Cobra Monaco Pro FIA Motorsport Bucket Seat | Base Mount, Side mount | FIA 8855-1999 | Seat only; 292 x 330 mm base or a suitable side-mount system. |
| OMP Champ-R Fibreglass FIA Motorsport Seat | Side mount | FIA 8855-1999 | Seat shell and its prescribed side mounts. |
| OMP First R Fibreglass FIA Motorsport Seat | Side mount | FIA 8855-1999 | Seat shell and its prescribed side mounts. |
| Mirco GT 3D Fabric FIA Motorsport Seat | Side mount | FIA 8855-1999 | Side supports and shell clearance; colour choices do not prove fit. |
| Mirco RS2 3D Fibreglass FIA Motorsport Seat | Side mount | FIA 8855-1999 | Side supports; allow room for the lateral head-support wings. |
| Sparco Rev QRT FIA Motorsport Bucket Seat | Side mount | FIA 8855-1999 | Seat only; prescribed side supports and Civic lower assembly. |
| Sparco Grid Q FIA Motorsport bucket seat | Side mount | FIA 8855-1999 | Seat only; prescribed side supports and Civic lower assembly. |
| Corbeau Sprint X System 3 FIA Motorsport Bucket Seat | Side mount | FIA 8855-1999 | FIA 8855-1999; System 3 is shell construction. Corbeau Pro-Team mounts/M10 12.9. |
| Reclining sport seats | |||
| Auto Style Type BS5 Reclining Seat | Base Mount | No FIA competition approval established | Includes sliders; 345 x 280 mm listed. Check slider lower interface. |
| Auto Style Type JW Reclining Seat | Base Mount | No FIA competition approval established | Includes sliders; 345 x 280 mm listed. Check slider lower interface. |
| Auto Style Type MS Reclining Seat | Base Mount | No FIA competition approval established | Includes sliders; 345 x 280 mm listed. Check slider lower interface. |
| Sparco R100 Martini Racing Reclining Sport Seat | Base Mount | No FIA competition approval established | Seat only; 345 x 271 mm base. |
| Sparco R333 Reclining Sport Seat | Base Mount | No FIA competition approval established | Seat only; 345 x 271 mm base. |
| Sparco R500 Fabric Reclining Sport Seat | Base Mount | No FIA competition approval established | Seat only; 345 x 271 mm base. |
| Sparco R500 Sky Reclining Sport Seats | Base Mount | No FIA competition approval established | Seat only; 345 x 271 mm base. |
| OMP RTS Reclining Sport Seat | Base Mount | No FIA competition approval established | 345 x 270 mm base listed; verify exact drawing. |
| Cobra Misano Anniversary Reclining Sport Seat | Base Mount | No FIA competition approval established | Seat only; required base specification; 291 x 330 mm standard pattern. |
| Cobra Misano Anniversary Spec 2 Reclining Sport Seat | Base Mount | No FIA competition approval established | Seat only; required base specification and side; 291 x 330 mm standard pattern. |
Common questions
Does an EG frame fit every Civic with an EJ code?
Check the full chassis and generation. EJ occurs in fifth-generation coupe applications and on later Civics. A product’s exact application must match the car; the letters alone are insufficient.
Why do some EG applications start in 1991 and others say 1992?
The catalogues use different application dates and markets. BRIDE lists its Japanese-market EG6 from September 1991, while Planted lists the Civic 1992-1995. Match the maker’s exact application and original chassis.
Does a 1996 registration mean I need an EG kit?
It does not identify the floor by itself. M2 uses a “92-96 EG” description, but later Civics have separate applications. Send the chassis code, body and original market with the registration.
Which side is Planted SB041DR?
Physical left, called driver by Planted and RHD passenger in our shop. SB041PA is physical right and the shop’s RHD driver option. Confirm the market-specific floor as well as the side.
Is Planted's Standard upper pattern the same as Alternate?
The maker says Standard includes the RECARO slider pattern; Alternate substitutes the Cobra/Scheel-Mann arrangement. Confirm the exact slider and which version the supplied shop bracket has.
Do I need separate runners with the PCI slider kit?
The PCI sliding assembly includes its slider system and specified S1 side supports. Choose the handed kit and confirm seat compatibility before adding hardware.
Can the PCI adjustable fixed mount slide while I am seated?
It is adjusted through its installation hardware. Choose the separate PCI sliding assembly if fore-and-aft movement after installation is required.
Does the M2 base-mount option include adaptation bars?
Confirm the selected package with us. The shop has base and side options, while M2’s standard rail is designed for side mounting. Add separate bars only once the actual supplied base conversion is clear.
Can I order both front-seat frames together?
The paired M2 listing is available for this EG/DC2 family. Confirm the left and right assemblies and the upper fittings together; seats are separate.
Which BRIDE code is for an RHD driver?
For this EG6 family H033 is physical right, the RHD driver side; H034 is physical left. The suffix must also match the required rail type and exact seat.
Can a BRIDE EG6 rail be assumed to fit every fifth-generation body?
BRIDE’s current matching result concerns the front-wheel-drive EG6 and its catalogue is principally for cars sold in Japan. Have other chassis, bodies or market floors confirmed separately.
Why are RO and XR different if both show 260 × 405 mm?
They have different listed seat applications. Use BRIDE’s exact seat and vehicle results alongside the fixing dimensions.
Do all the reclining seats fit the Sparco pattern?
The current Auto Style products specify 345 × 280 mm, compared with 345 × 271 mm for the named Sparco recliners. Cobra and OMP options also need their own exact interface checked.
Do the Auto Style recliners need another slider kit?
The listed BS5, JW and MS include sliders. Confirm the supplied slider’s lower holes against the chosen Civic base before buying more hardware.
Is Corbeau System 3 a newer FIA standard?
It is a shell-construction designation. The current Sprint X System 3 listing and maker’s Sprint X specification identify FIA 8855-1999; check the actual label and prescribed side supports.
Is Takata Drift III a six-point harness?
The current Drift III listing is four-point, as is Drift II. A six-point racing installation needs its own suitable harness, seat openings and anchorage arrangement.
Does a four-point Clubman include a crotch strap?
A standard four-point layout has four vehicle attachments and does not establish that a crotch strap is supplied. Check the exact product and instructions; use a specified six-point system where required.
Is a roll cage always required solely because the harness has six points?
Point count alone cannot approve an installation. Follow the restraint maker’s anchorage and routing requirements and the event’s roll-protection rules. A random cage tube or harness bar does not establish suitable attachment points.
Which Custom Cages kit is linked here?
The live product is 18914, HO/98T for the EG6, in T45 with weld-in multipoint construction. Verify the exact shell and the kit’s installation and certification requirements.
What information should I send for a complete fitting check?
Send the full chassis code, body, year and original market; RHD or LHD and physical side; the exact seat and intended use. Include any existing runner or frame part numbers and photographs of altered floor mounts.
More help
Send the seat model and chassis details together through our contact page or call 0115 647 8650. We can work through the floor base, upper supports, adjustment and restraint arrangement before the order is placed.
Back to the Car Seat Selector guide.
Manufacturer fitting information: Planted application guide and FAQ; BRIDE matching and rail specifications; M2 Honda rail catalogue; PCI slider and adjustable specifications; Corbeau Sprint X; Custom Cages EG6 HO/98T; TRS instructions; Schroth instructions.
Need a personal recommendation?
We're here to ensure you pick the right seat.
Contact us today.



































