The Polo Mk3 has a one-make racing series named after it, which tells you something about what the chassis is capable of. The standard seats do not match that pedigree: they sit you too high, the bolsters soften with age, and on most examples at this mileage the foam has long since stopped doing its job. A reclining sport seat on a proper fitting frame lowers your hips and gives you real lateral support through a corner. The recline adjustment stays, so the car still works for a passenger or a long run.
Two frame routes are in stock for the 6N Polo: Cobra and Sparco. The frame is the vehicle-specific adapter that replaces the standard runner assembly and bolts to the factory floor mountings. It sets your seat height and decides which bolt pattern your seat needs. Frame first, then seat.
We stock a fitting frame for the 6N from Cobra and from Sparco. A frame is the vehicle-specific adapter that bolts to the factory floor mounting points in place of the standard runner assembly, and it sets your final seat height. The Cobra subframe is a complete kit: the base frame and the sliding runner ship in the same box. The Sparco sub-frame is the adapter bracket only, priced per side, and you pair it with a separate Sparco runner kit.
One note on the Sparco route: these sub-frames do not include a seatbelt clip anchor point. If you are keeping the standard diagonal seatbelt rather than running a harness, you will need a separate belt anchor on the seat side. Most drivers fitting them are running a harness, but it is worth knowing before you order.
Part SU-VW-PO3, £231.66 inc VAT each. Includes the sliding runner. Takes Cobra 291mm seats and Corbeau recliners.
Part 00499073, £87.00 inc VAT per side. Sold individually. Add a Sparco runner kit (£78.00 a pair). Takes Sparco and Corbeau seats drilled for 345mm.
Every reclining seat we sell bolts down through a base mount pattern. On this car, two patterns matter. Cobra recliners use 291mm x 330mm, which the Cobra subframe is built around. Sparco recliners use 345mm x 271mm, and they go on the Sparco sub-frame. Neither pattern lines up with the other frame. The exception is Corbeau: both the SVR and the RRS are drilled for both patterns, so they bolt to either frame in the table below.
| Seat | Bolt pattern | Cobra subframe | Sparco sub-frame |
|---|---|---|---|
| Sparco R100 | 345 x 271 | No | Fits |
| Corbeau SVR / RRS | 291 or 345 | Fits | Fits |
| Cobra Daytona | 291 x 330 | Fits | No |
| Sparco R500 | 345 x 271 | No | Fits |
| Cobra Stuttgart | 291 x 330 | Fits | No |
The R100 is the most popular recliner we sell, and for a Polo Mk3 it is usually where people start. It is a compact seat with an open base, which matters in a cabin this size. The side bolsters give you support without fighting the door card on the way in, and the recline knob clears the centre console on the cars we have fitted them to. Sparco rate it for all waist sizes and for drivers both under and over six foot, so it is hard to be the wrong shape for it. Pair it with the Sparco sub-frame and a runner kit and you have the complete setup at the lowest price point in this guide.
The SVR and the RRS are Corbeau’s two reclining designs, and both are drilled for 291mm and 345mm patterns. On a Polo Mk3, where you are committing to one frame brand, that dual-fit capability has genuine value: either seat works whichever frame route suits your budget. The SVR has a smoother outer shell with an integrated headrest and an optional heating element. The RRS has a more sculpted backrest and comes in a low base version that recovers a few centimetres of headroom, which helps in a compact car. Cameron reaches for the SVR for daily use; the RRS Low Base is the recommendation when headroom is tighter or the driver is on the taller side.
The Daytona is Cobra’s everyday recliner, and the one most people reach for when the Polo is doing track evenings alongside regular road use. It has more pronounced bolsters than either Sparco, so your body stays put mid-corner without you bracing, but it is not so deep that getting in and out of a small car becomes difficult. Cobra build it with a steel frame and fibreglass outer shell, and it goes straight onto the Cobra subframe where the sliding runner is already in the box. If you are deciding between the Daytona and the Stuttgart, the Daytona is the track-biased pick; the Stuttgart adds more padding and trim options for daily comfort.
The R500 sits above the R100 with a taller backrest and more shoulder support. Dual density foam in the base and the backrest holds its shape better over a long run and gives slightly more resistance under load in a corner. It is available in fabric or the easy-clean Sky vinyl. The pattern and the frame route are the same as the R100, so if you start with the R100 and find you want more upper body support later, you can swap the seat without changing the frame. Pick it over the R100 if you do occasional track sessions and want more shoulder contact without going to the deeper bolsters of the Cobra range.
The Stuttgart is Cobra’s comfort-oriented recliner: slightly wider in the seat base than the Daytona, with more padding in the cushion. It is built to order through Cobra’s Signature range, which means heating, lumbar support and contrast stitching are on the options list if the Polo does all-weather commuting. The vinyl version is the most practical starting point for a car that sees wet-weather use. Like the Daytona, it goes on the Cobra subframe with the sliding runner already included in the frame price. If you are choosing between the two, the Stuttgart is the daily-use pick with comfort extras on the options list; the Daytona is the track-biased seat at a similar price.
Both frames bolt to the 6N Polo’s factory seat mounting points, so there is no drilling on a standard floor. Torque the floor bolts to the manufacturer’s spec and check seat belt buckle clearance after fitting, because a sport seat often moves the buckle somewhere new. The Cobra subframe ships with its sliding runner in the box, so the frame is the only order before the seat. The Sparco sub-frame is the adapter bracket only, and you add a Sparco runner kit alongside it. Both frames are priced per seat position, so a pair of seats means two frames in the basket.
| Your seat | Frame to order | Runners |
|---|---|---|
| Sparco R100 or R500 | Sparco sub-frame, per side | Sparco runner kit, £78.00 a pair |
| Corbeau SVR or RRS | Sparco sub-frame, per side | Sparco runner kit, £78.00 a pair |
| Corbeau SVR or RRS | Cobra subframe, each | Included in frame price |
| Cobra Daytona or Stuttgart | Cobra subframe, each | Included in frame price |
| Seat | Bolt pattern | Waist | Height | Weight | Price inc VAT |
|---|---|---|---|---|---|
| Sparco R100 | 345 x 271 | All sizes | Over and under 6ft | Not published | From £282.00 |
| Corbeau SVR / RRS | 291 or 345 | 32 to 38in | All heights | Not published | From £498.00 |
| Cobra Daytona | 291 x 330 | 32 to 38in | All heights | Not published | £599.00 |
| Sparco R500 | 345 x 271 | 32 to 38in | All heights | Not published | From £329.00 |
| Cobra Stuttgart | 291 x 330 | 32 to 38in | All heights | Not published | From £619.00 |
Prices include VAT and were correct on 31 August 2026. Where a weight says not published, the manufacturer does not give one and we will not guess it. Waist and height figures are the manufacturers’ published fitment ranges; if you are on a boundary, ask us before ordering.
No. Both frames bolt to the 6N Polo's factory seat mounting points without any drilling. Check the seat belt buckle clearance after fitting, because a sport seat often changes where the buckle sits.
No, it does not. The Sparco sub-frames for the Polo Mk3 are listed without a seatbelt clip anchor point. If you are keeping the standard diagonal seatbelt, you will need a separate belt anchor on the seat side. Most drivers fitting them are running a harness, but it is worth sorting before you install.
No. The Cobra subframe is built around the 291mm x 330mm pattern, and Sparco recliners use 345mm x 271mm. The two do not line up. The Corbeau SVR and RRS are the only seats in this guide drilled for both patterns, so they bolt to either frame.
Every seat in this guide is listed by its manufacturer as 4 point compatible, with harness slots in the backrest. If you are planning harnesses, let us know when you order and we will make sure the whole setup works together.
We have a customer question on the blog that covers an exact seat fitment in the Polo 6N: Can I Fit The Mirco MX5 Seat Into My VW Polo 6N MK3? If you have a seat in mind that is not in this guide, ask Cameron before ordering and we will check the exact fitment.
If it were my money in a Polo Mk3: the R100 on the Sparco sub-frame for a daily driver on a budget. It covers most of what you are after at the lowest outlay, and if the car moves on, the frame is not a big investment to leave behind. The SVR or the RRS Low Base if you want both frame routes kept open or you are on the taller side. The Daytona on the Cobra subframe if your Polo does regular track evenings and you want more bolster contact than the Sparco range gives you. The Stuttgart in vinyl if the car is doing daily mileage in all weather and you want something you can wipe down, with heating on the options list. And the R500 sits between the R100 and the Cobra picks: more shoulder support than the R100, same Sparco frame route, sensible step up if the R100 feels too open.
Every setup listed here bolts straight to the 6N Polo’s factory floor. If you are between two seats or unsure about sizes, call us on 0115 9893488 and Cameron can run through the combinations before you commit.
The five reclining sport seats we rate for the Volkswagen Polo Mk3, with the Cobra and Sparco frame routes that bolt each one straight to the factory mounting points.
A customer is putting VXR Recaro buckets in a 2014 Polo 6C and wants harnesses with no roll cage and the rear seats still working. The answer is the clip-in harness: eye bolts in the standard anchorage threads, snap hooks off in seconds, from £120.00.
The five reclining sport seats we rate for the Volkswagen Passat B8 chassis, with the Cobra direct-fit subframe and Planted Technology bracket routes that bolt each one to the factory mounting points.
Every Sim-Lab cockpit is an aluminium profile rig, so almost any motorsport seat bolts on. Which seats suit the GT1 Evo, GT1 Pro, P1X Pro, P1X Ultimate and X1 Pro, whose brackets to use, and what each route costs from £360.
The five reclining sport seats we rate for the Volkswagen Jetta Mk5, with the Cobra direct-fit subframe and Planted Technology bracket routes that bolt each one to the factory mounting points.
A bucket seat on direct fit side mounts sits as low as a Megane R26 will physically allow. Here are the two ways a seat mounts in one, and what both builds cost per side.
Hundreds Of Products Ready Today. Dispatch/Collection 
