Ford Mustang II Bucket Seat Guide
Mustang II: build the 1974 to 1978 fitting plan around SB170
The Mustang II needs its own seat-fitting plan. Planted lists SB170 for the 1974 to 1978 car, with separate physical-left and physical-right versions. Match the actual model year and body before choosing the seat and upper fittings.
This guide compares fixed-back buckets and reclining seats with the current frame and selected upper parts. It keeps the earlier classic Mustang and the later Fox-body application separate.
Garreth can compare the support and access you need. Cameron can assess the proposed assembly and finished driving position. Include the actual steering arrangement and any previous mounting-area work.
At a glance
- Planted SB170 application: Ford Mustang 1974 to 1978; actual Mustang II year and body confirmed.
- Physical right: SB170PA, shop RHD driver; physical left: SB170DR, shop RHD passenger.
- Include the actual steering arrangement with the full supplied physical-side reference.
- Standard and Alternate upper patterns are confirmed separately from the side selection.
- A seat pair requires a complete position-specific fitting assembly for each seat.
- Assess cabin access, restraints and any cage application with the actual installed position.
Start with the 1974 to 1978 Mustang II application
Mustang II is the second-generation car covered here. Planted lists its SB170 bracket for the 1974 to 1978 Mustang. Send the actual model year and body with the enquiry, including any previous seat conversion.
The preceding Mustang uses a separate SB213 application. Our Classic Mustang guide explains that earlier range and its body exclusions. It does not establish an SB170 installation.
For the 1979 onwards car, use the separate Fox Body and early SN95 guide. A Mustang name on a seat frame is insufficient to identify the correct lower connection. Garreth can compare the exact car and seat before the parts list is settled.
Order SB170 by the physical seating side
The current shop listing offers SB170PA as RHD Driver Side and SB170DR as RHD Passenger Side. Put physical right or physical left beside that choice. Include the actual steering arrangement, particularly if the car has been converted.
SB170PA is the physical-right bracket; SB170DR is physical left. Planted names those versions Passenger/Right and Driver/Left for its market. An LHD driver therefore sits on the DR side; an RHD driver sits on the PA side.
One bracket is required for each position being changed. Cameron can compare the supplied reference with the actual mounting area and retained hardware. Upper fittings and the seat are specified separately.
-
From £222.60 Incl. VATFrom £185.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Confirm the slider pattern before choosing the upper assembly
Planted provides Standard and Alternate upper patterns. Standard includes the RECARO slider arrangement; Alternate substitutes the Cobra and Scheel-Mann pattern. The shop seating-position dropdown identifies the side, so confirm the supplied upper pattern with the order.
Cobra runners have Narrow and Wide versions in Planted guidance. Match the exact runner and its two fixing interfaces to the seat and supplied SB170. Do not use a seat-base measurement as a substitute for that runner-to-frame check.
A fixed assembly also needs its own permitted connection. Check the exact seat and support instructions before choosing hardware or changing a mounting pattern. Have any required work assessed by the installer.
| Item | Reference | Check with the order |
|---|---|---|
| Vehicle | Mustang 1974 to 1978 | Actual Mustang II model year, body and mounting area |
| Physical right | SB170PA | Shop RHD driver; LHD passenger |
| Physical left | SB170DR | Shop RHD passenger; LHD driver |
| Standard | RECARO slider arrangement included | Exact runner version and both fixing interfaces |
| Alternate | Cobra and Scheel-Mann substitution | Supplied pattern confirmed separately from the seating side |
| Seat pair | Two position-specific lower assemblies | Seat quantity does not include the complete fitting parts |
Include adjustment and finished height in the fitting plan
Cobra Premium SUBFR07EL and Sparco 0049306 runners are options to assess with the exact seat and bracket pattern. Check usable travel and access to the release handle. The runner adds to the finished seat height.
A side-mounted shell needs suitable supports between its fixing points and the lower assembly. The Sparco steel supports below are an option for a compatible seat. Their orientation and connections must follow the relevant component instructions.
For competition use, Cobra mounting guidance specifies direct side mounting without runners. Check the actual permitted lower assembly and event requirements before choosing that route. Garreth can compare the seat options while Cameron checks the proposed driving position.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Compare the steel-frame seats by the actual mounting dimensions
Cobra Monaco Pro, Sparco Sprint and OMP TRS-E Velour are fixed-back steel-frame options. Their current shop listings offer base and side mounting. Decide which method the complete installation will use before selecting the upper fittings.
Monaco Pro is listed at 292 x 330 mm on its base, Sprint at 345 x 271 mm and TRS-E at 345 x 270 mm. Preserve those differences when comparing the parts. Confirm the actual supplied seat drawing and the mating component.
The current listings state FIA 8855-1999 approval. Check the supplied seat version and label against the intended event. The seat approval does not establish the Mustang II floor connection or the rest of the installation.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Consider the Cub with headrest as a base-mounted option
The Cobra Cub shown here is the fixed-back version with a headrest. Its current shop listing states base mounting at 291 x 330 mm. Have that exact seat version and its upper fittings compared with the supplied SB170 pattern.
The Cub is listed for road and track use without FIA competition homologation. Check the support and headrest position with the driver. A period appearance does not determine suitability for an event or a particular restraint.
Cobra general mounting guidance describes 292 or 405 x 330 mm base arrangements. Obtain the relevant supplied-seat and runner drawings where the listed dimensions differ. Cameron can include the complete assembly in the cabin trial.
-
From £349.00 Incl. VATFrom £290.83 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Assess recliners with the access and movement you need
Cobra Le Mans Heritage is a period-style reclining option with a listed 291 x 330 mm base pattern. Compare the finished position and trim with the driver. Confirm the actual seat version and the complete runner arrangement.
Sparco R100 is another base-mounted recliner, listed at 345 x 271 mm. Allow room to operate the recline control and move the backrest through its useful range. Check that movement with the door and centre area of the actual car.
The Corbeau RRS listing supplies two seats. Its attributes list 291 x 330 mm and 345 x 271 mm, so confirm which arrangement the supplied version uses. Order the correct position-specific lower assemblies and upper parts separately for both seats.
Garreth can compare the fixed-back and reclining choices with the access you require. Include any use of the rear seating in that discussion. A reclining backrest alone does not prove that the finished installation provides enough access.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £649.00 Incl. VATFrom £540.83 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Trial the complete seat in the actual Mustang II cabin
Check the mounting area before covering it with the new assembly. Repairs, replacement floor panels and earlier seat changes need assessing with the proposed bracket. A listed model year does not describe the condition of an individual car.
Sit the regular driver in the assembled position. Compare height and reach with the steering wheel and pedals. Check the shell shoulders or reclining backrest against the surrounding trim. Include access to seat controls and the belt buckle.
If a cage is part of the build, have its exact Mustang II body application and installation documents established separately. An earlier or later Mustang cage is not interchangeable evidence. Include the cage and the proposed restraints in the seat-position trial.
Choose restraints after checking the seat and actual anchors
The original belt and buckle arrangement needs checking with the replacement seat. Confirm the routing and access with the driver in position. A bracket application does not establish a complete belt installation.
Takata Drift II, TRS Magnum four-point and Schroth Profi 3×2 six-point are examples for a separate harness assessment. Follow the exact manufacturer instructions for routing and anchorage. Strap count does not prove that the car has suitable fixing points.
A six-point proposal needs an approved crotch-strap route through the actual seat and suitable attachments. Do not assume that the Cub or each recliner provides that route. Cameron can compare the proposed installation with the actual restraint instructions.
-
From £274.80 Incl. VATFrom £229.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £246.00 Incl. VATFrom £205.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £444.01 Incl. VATFrom £370.01 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Check the full assembly before the installation is finished
Start with the correct physical-side reference and compare the bracket with the actual mounting area. Resolve repairs or previous modifications against the supplied component instructions. Confirm the intended upper pattern before assembling the runner or supports.
Trial the complete seat and lower assembly with the driver. Check reach and finished height through the useful adjustment range. Verify operating clearances and the restraint path in that installed position.
Follow the relevant instructions for hardware, orientation and tightening. Have the completed connections assessed before the vehicle is used. Keep the actual supplied references with the installation details.
Send the car details and exact seat version for a fitting quote
Send Garreth the Mustang II model year and body with the actual steering arrangement. State the physical side for each seat being replaced. Include photographs of the mounting area and any previous work.
Cameron can compare the proposed assembly with the intended use. Include the parts already owned and whether adjustment is required. Send the actual restraint proposal with the enquiry.
- Actual 1974 to 1978 Mustang II model year and body.
- Physical left or right with the actual steering arrangement and SB170DR or SB170PA reference.
- Exact seat version, supplied upper pattern and runner or support arrangement.
- Seat quantity and a separate complete fitting assembly for each position.
- Mounting-area condition, required access and restraints to assess.
Common questions
Which Mustang does this guide cover?
The Mustang II covered by the Planted SB170 application for 1974 to 1978; confirm the actual model year, body and mounting area.
Does the earlier SB213 bracket replace SB170?
SB213 is a separate earlier Mustang application with its own body exclusions; use the correct named application for the actual car.
Is the 1979 Fox-body car included?
Use the separate Fox Body and early SN95 guide; the 1979 onwards application is distinct from Mustang II.
Is the registration year enough to select the frame?
Send the actual model year and body together with the mounting-area details, including repairs or any previous seat conversion.
Which SB170 version is physical right?
SB170PA is physical right and the shop RHD Driver Side order; on an LHD car it is the passenger position.
Which SB170 version is physical left?
SB170DR is physical left and the shop RHD Passenger Side order; on an LHD car it is the driver position.
What if the car has been converted to RHD?
State the actual steering arrangement and physical seating side, and have any altered mounting area assessed with the supplied bracket.
Does one frame order fit both seats?
Specify the correct position-specific lower assembly for each seat being changed; seat-pair quantities and fitting quantities are separate.
Is the Standard or Alternate upper pattern chosen by the side dropdown?
The shop side choice does not establish the supplied upper pattern; confirm that pattern with the actual runner version before ordering.
Why check the Cobra runner width?
Planted distinguishes Narrow and Wide Cobra runners; match the exact version and both fixing interfaces to the supplied assembly.
Can runners be used for every competition installation?
Cobra competition mounting guidance specifies direct side mounting without runners; check the selected seat instructions and actual event requirements.
Are the three steel-seat base patterns identical?
The shop lists Monaco Pro 292 x 330 mm, Sprint 345 x 271 mm and TRS-E 345 x 270 mm; confirm the actual supplied drawings without rounding the differences away.
Does seat homologation approve the whole installation?
Check the supplied version and label against the event, and assess the complete vehicle mounting and restraint installation separately.
Is the headrest Cub side mounted?
The current Cub with headrest listing is base mounted at 291 x 330 mm; confirm the exact supplied seat and upper fittings.
Is the Cub an FIA competition seat?
Its current listing does not provide FIA competition homologation; check the actual driver support, restraint proposal and intended-use requirements.
Why confirm 291mm against general Cobra guidance?
The shop seat listings and general maker guidance use different figures; obtain the actual supplied seat and runner drawings before selecting the complete assembly.
What does the RRS pair listing include?
It supplies two seats; the actual seat version, position-specific frame assemblies and upper fittings are specified separately.
Will a recliner automatically preserve rear access?
Trial the finished seat position and useful backrest movement with the actual car; check the access you require before completing the order.
Can an earlier Mustang cage be ordered for Mustang II?
Have the exact Mustang II body application and installation documents established; an earlier or later Mustang cage name does not prove interchangeability.
Does a harness need its own mounting assessment?
Yes; use the exact restraint instructions and assess the actual anchors, routing and driver position separately from the seat-frame choice.
Do four straps prove there are suitable factory anchors?
Strap count does not establish the condition, strength or permitted use of the actual mounting points; follow the restraint instructions.
Can all of these seats take a six-point harness?
The actual seat must provide a permitted crotch-strap route with suitable attachments; assess the complete restraint installation independently.
What should be checked in the cabin trial?
Include installed height and reach, seat and control clearances, useful adjustment, the belt path and any rear-access requirement.
What information helps with a quotation?
Send the actual model year, body, steering arrangement, physical seating side and exact seat version, with mounting-area photographs and details of any existing parts.
Garreth’s top tip
Choose the seat around the support and access you need in the actual Mustang II. Bring the precise model year and body into the fitting discussion early. Compare the complete position before committing to the trim.
Cameron’s fitting view
Write the physical side beside SB170DR or SB170PA and the actual steering arrangement. Confirm the upper pattern with the runner or supports. Trial the whole assembly and restraint path with the driver.
Plan your Ford Mustang II seat change
Drop us an email or open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Manufacturer references: Planted Mustang II physical-left bracket, physical-right bracket and Cobra mounting guidance. Confirm the exact supplied seat, runner and bracket versions with the installation documents.











