Toyota Starlet 60 Series 1978 to 1984 Bucket Seat and Fitting Guide
Choose the 60 Series fitting route before the seat package
Which seat fittings do you need for a Starlet 60 Series? Our listed Planted SB283 names the second-generation 1978 to 1984 application. Start with that exact car, then choose the support and adjustment you want from the seat.
Garreth would try the cushion and getting over the bolster before choosing a trim. Cameron would check the chassis details and current mounting points. An earlier seat conversion needs to be included in that conversation.
At a glance
- SB283 names Toyota Starlet second generation / 60 Series, 1978 to 1984.
- The maker identifies SB283DR as physical left and SB283PA as physical right; confirm the supplied shop variation and steering side.
- EP82 and EP91 rail listings refer to other named Starlet applications and need separate guides and fitting checks.
- Record the actual body and original floor, plus any changes made during an earlier seat installation.
- Choose the vehicle bracket, runner or fixed connection and shell supports as a complete assembly.
- The scaled Sparco drawing describes named seat-side centres; the Starlet floor needs its own reference.
Identify the 60 Series and the mounts it has now
Planted’s application records name the second-generation Toyota Starlet on the 60 Series, 1978 to 1984. Send the chassis identification and build details when checking that application. Include the body and steering side as well.
Our catalogue also contains BRIDE rail listings naming EP82 and EP91 cars. A Toyota Starlet label alone does not distinguish those applications. Keep the actual chassis reference with the parts enquiry.
Photograph the original mounting locations and any existing adapters or alterations.
Tell us how the car is used and which seating positions need changing. If access behind the front seats matters, include that requirement before choosing the shell. Cameron would check the proposed access and driving position together.
Choose the SB283 physical side and supplied version
The SB283 listing provides the floor-bracket route for the maker’s named 60 Series application. Its references are SB283DR for physical left and SB283PA for physical right. Match that physical position to the actual car.
Our shop options use RHD driver and passenger wording, so confirm the full supplied variation code with the steering side.
Ask for the complete parts list for each seat position. The floor bracket, upper connections and retained buckle arrangement need checking together. A pair of seats also needs the right quantities for both sides.
| Physical position | Manufacturer reference | Cobra alternate reference |
|---|---|---|
| Left | SB283DR | COBRA-SB283DR |
| Right | SB283PA | COBRA-SB283PA |
-
From £224.95 Incl. VATFrom £187.46 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Match the runner pattern as well as the physical side
Planted distinguishes Standard and Alternate slider-pattern versions. Its general FAQ directs wide Cobra and Scheel-Mann runners to the Alternate pattern. The narrow Cobra runner pattern is included on both.
The exact SB283 application records also name the Cobra-prefixed alternate references shown above.
Send the full runner and seat references before choosing the supplied bracket version. Compare both fixing interfaces in the proposed assembly. Cameron would resolve that pattern choice alongside the physical seating side.
Compare fixed-back seats by support and mounting route
The Cobra Monaco Pro is a fixed-back steel-frame option with listed base and side mounting routes. Try its support and bolster access before choosing the trim. The exact seat version and lower fittings still need matching.
The standard Sparco Sprint card carries the BRR0003 family reference; the maker catalogue shows base and side fixing routes.
The OMP TRS-E Velour is another steel-frame candidate with base or side mounting listed. Compare the cushion, shoulder support and getting in and out. Garreth would make that driver choice before completing the 60 Series fitting enquiry.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Try reclining choices with their controls and lower fittings
The Sparco R100 gives you a base-mounted reclining option to discuss. Our linked listing uses legacy reference 00961NR, while the newer catalogue uses the 009014 family. Confirm which version is supplied before selecting fittings from its drawing.
The Corbeau Sportline RRS card is a pair of seats on the listed standard base. Specify each physical position’s vehicle bracket and upper assembly separately. Confirm the actual package contents and quantities.
The Cobra Misano Anniversary provides another shell and reclining mechanism to try. Allow for the backrest movement and access to its controls beside the actual door and tunnel. Check any access needed behind the seat with the full assembly in position.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Match the Cobra runner to both connections
The Cobra Premium runner listing offers 291mm and 405mm handle-width choices. Select the runner for the exact seat and supplied SB283 pattern. The handle-width label alone cannot establish the lower hole positions.
Include the complete Monaco or Misano reference when asking about the runner.
Check the seat-to-runner connection and runner-to-bracket connection independently. Trial the travel and room for the release handle in the actual cabin. Include the runner thickness when comparing the finished driving position.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Specify the Sparco slider with the actual seat version
The Sparco 0049306 runner is a sliding option to consider with the named Sparco seats. The catalogue shows a 271mm longitudinal fixing distance. Confirm the complete upper and lower layouts against the supplied seat, supports where used and SB283 bracket.
The named Sprint and R100-family seat-side base fastening below is 345mm by 271mm.
Trial both rails through the movement needed by the driver and check that they release and lock together. Include the handle and surrounding trim in that trial. Matching one dimension leaves the other connections to confirm.
Use supports specified for the chosen side-mounted shell
For a side-mounted shell, supports join the seat’s side fixings to the lower assembly. The Sparco steel supports shown here are a candidate for the selected Sparco shell and its instructions. Confirm a different seat family’s own support combination.
The shell’s side fixings and the support’s lower pattern need separate drawings.
Cameron would check the shell label, support orientation and specified fasteners before comparing the connection below. Include any runner and the actual SB283 version in that comparison. The named floor application alone cannot specify those upper fittings.
Plan fixed positioning as its own complete arrangement
Planted publishes installation arrangements for base-mounted and side-mounted seats, with and without sliders. Its FAQ describes its own side mounts around an arrangement with sliders beneath them. A fixed assembly needs its own connection and position check.
Ask us to specify the complete fixed arrangement if sliding adjustment is not wanted.
Use the instructions for the actual components when trialling the proposed assembly in the car. Check pedal and steering reach with the driver. Garreth would also try getting over the bolster and any access needed behind the seat.
See the named Sparco seat-side centres at one scale
The named Sprint and R100-family lower fastenings in the Sparco catalogue measure 345mm across and 271mm front to rear. Both dimensions use the same scale in the drawing. Confirm the supplied seat version before choosing parts around those centres.
The Starlet floor, full SB283 slot layout and outside seat dimensions each need their own measurements.
Trial the preferred shell and lower fittings in the actual cabin. Include shoulder room, cushion position and access to the controls. A Cobra, Corbeau or OMP choice needs that exact version’s drawing for its seat connection.
Source: Sparco 2025 manufacturer catalogue, printed pages 178 and 326 to 327. The shop’s R100 reference needs supplied-version matching.
Choose the restraint with the shell and actual anchors
Describe the intended belt arrangement before finalising the lower fittings. Check the exact seat and restraint instructions against the actual anchors and occupant. Include the existing buckle connection in the photographs.
If a harness is part of the plan, show any proposed bar or cage and its specified attachments.
The shell openings, strap arrangement and anchor locations need checking together. Trial the routing and buckle access with the seat in its intended position. Select the harness product once that configuration is established.
- Original belt: check the exact shell, buckle position and retained mounting hardware.
- Harness: confirm the required straps, shell openings and available anchor arrangement together.
- Two seats: specify each physical side, quantities and the adjustment needed by each occupant.
Send the chassis details and a complete seat plan
Send the chassis identification, build, body and steering side with photographs of the original mounts. Show the current brackets and any previous adaptations. Include the exact seat, runner or fixed connection and support references.
Tell us how much adjustment and rear access you need, plus the functions and belt arrangement you want to retain.
Measure the existing driving position if you want to change its height. Cushion thickness, shell angle and the lower components all contribute to the result. Cameron would trial the complete proposed position with the driver before confirming reach and clearance.
Common questions
Which Starlet does the SB283 application name?
Planted names the second-generation Toyota Starlet on the 60 Series, 1978 to 1984. Match that reference to the actual chassis, original floor and supplied bracket. Include any previous seat-mounting changes.
Can I use the EP82 or EP91 rail listings for a 60 Series?
Those listings name other Starlet applications. Keep the actual chassis reference with the fitting enquiry. A shared Starlet model label does not establish the same floor connection.
Which SB283 code is physical left or right?
The maker identifies SB283DR as physical left and SB283PA as physical right. Cobra-prefixed alternate references keep those physical positions. Confirm the actual steering side and full supplied shop variation code.
How do I match the RHD shop options to those codes?
Specify the actual physical seat position and steering side together. Ask us to confirm the full supplied variation reference against the manufacturer application. Keep that code on the parts list for the position being changed.
What if the car already has modified seat mounts?
Send photographs showing the original mounting locations and current adapters or alterations. Include details of the previous conversion where known. The named application must be checked against the floor and assembly the car actually has.
How do Standard and Alternate runner patterns differ?
Planted’s general FAQ directs wide Cobra and Scheel-Mann runners to the Alternate pattern and includes narrow Cobra runner fixings on both. Confirm the exact seat, runner and supplied SB283 version. Check both fixing interfaces.
Does the RRS pair include two Starlet brackets?
The linked card describes a pair of seats on the named standard base. Specify the vehicle bracket and selected upper assembly for each physical side separately. Confirm the actual contents and quantities before ordering.
Can I choose a fixed seat position?
Ask us to specify the fixed assembly for the exact shell and car. Planted publishes separate installation arrangements with and without sliders. The connection and final driving position need checking for the selected arrangement.
Does a reclining seat settle the rear-access question?
Trial the actual backrest movement, controls and complete assembly in the car. Describe the access you need before selecting the seat. The floor-bracket application alone cannot establish usable access.
Does the 345mm by 271mm diagram show the Starlet floor?
It shows named Sparco seat-side fastening centres from the manufacturer catalogue. The actual Starlet floor and full SB283 slot layout need separate references. Confirm the supplied seat version and each remaining connection.
How much lower will the seat sit?
Measure the existing position and trial the proposed complete assembly with the driver. The cushion, shell angle and fittings below it all affect the result. An SB283 code alone cannot give a height reduction.
What should I send for a complete recommendation?
Send the chassis identification, build, body, steering side and mounting photographs. Include the exact seat and fittings, adjustment and rear access wanted, retained functions and intended belt arrangement. Tell us about previous adaptations.
Garreth’s top tip
Garreth would choose the support, cushion and bolster access that suit the driver before deciding on the trim. Include everyday entry and any access needed behind the seat. Specify the lower assembly around that exact choice.
Cameron’s fitting view
Cameron would keep the 60 Series chassis reference and actual floor photographs beside the SB283 parts list. Match the supplied physical side and pattern before choosing the upper connections. Trial the complete position and access with the driver.
Plan your Toyota Starlet 60 Series 1978 to 1984 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Sources: Planted application records, slider-pattern and market guidance and assembly-specific instructions; Sparco 2025 catalogue, printed pages 178 and 326 to 327; linked shop listings. Confirm the current supplied versions and actual car before completing the package.

![Planted Technology Toyota Starlet [2nd Generation / 60 Series] (1978-1984) Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/SB283PA-1-300x300.jpg)





