Toyota Celica T160 1985 to 1989 Bucket Seat and Fitting Guide
Start with the exact T160 application and the car’s original floor
Which seat fittings should you choose for a Celica T160? The SB191 route listed here covers Planted’s fourth-generation 1985 to 1989 application, excluding All-Trac. Send the exact chassis and build details before choosing the seat and its lower fittings.
Garreth would try the cushion and bolster access with the driver. Cameron would start with photographs of the original mounting locations and any changes already made. Keep those details with the parts references through the fitting enquiry.
At a glance
- SB191 names Toyota Celica fourth-generation T160, 1985 to 1989, excluding All-Trac.
- SB191DR identifies physical left and SB191PA physical right; match the full supplied code to the actual steering side.
- Confirm the original chassis, body, build and floor, including any earlier conversions.
- Keep an All-Trac or GT-Four enquiry tied to its own exact manufacturer application.
- Specify the bracket, runner or fixed connection, supports and hardware for each physical position.
- The named 345mm by 271mm Sparco diagram refers to seat-side centres; the T160 floor needs its own reference.
Check the chassis and build against the named SB191 application
Planted names its SB191 application as Toyota Celica fourth-generation T160, 1985 to 1989, excluding All-Trac. Include the original chassis identification and build details with the enquiry. Give the actual body and steering side as well.
Photograph the mounting locations and any adapters or floor alterations already present.
The proposed seat does not settle which vehicle bracket belongs in the car. Cameron would keep the original vehicle identity beside the present floor photographs. Include previous fitting references where they are known.
Keep each Celica enquiry with its own bracket application
The All-Trac exclusion belongs with the SB191 reference throughout the enquiry. For an All-Trac or GT-Four, send its exact chassis and build for a separate manufacturer application check. Include any changes to the original floor.
The ST185 guide covers a later generation, so its parts list needs its own application checks.
Earlier Celicas and the later T200 and T230 cars also have separate fitting references. A shared Celica name does not establish interchangeable floor brackets. Use the guides below for the named later models.
Later-generation guides: Celica ST185 · Celica T200 · Celica T230.
Match the physical side and complete SB191 reference
The linked SB191 listing supplies the bracket route for the maker’s named T160 1985 to 1989 application, excluding All-Trac. SB191DR identifies physical left and SB191PA physical right in the manufacturer records. Confirm the position being changed before selecting the shop variation.
Match the RHD seating-side wording to the full supplied code and actual steering side.
List the upper fittings alongside the vehicle bracket. Include a runner or fixed connection, supports where needed and retained buckle hardware. Confirm each physical side and the quantities separately when fitting two front seats.
| Physical position | Manufacturer reference | Cobra alternate reference |
|---|---|---|
| Left | SB191DR | COBRA-SB191DR |
| Right | SB191PA | COBRA-SB191PA |
Select the runner pattern with the exact seat references
Planted’s general FAQ distinguishes Standard and Alternate slider patterns. Wide Cobra and Scheel-Mann runners require its Alternate pattern. The narrow Cobra runner fixings are included on both versions.
The SB191 records include Cobra-prefixed alternate codes for both physical sides.
Send the full seat and runner references before choosing the supplied bracket version. Compare the upper seat connection and the lower bracket connection independently. Cameron would confirm that complete arrangement before the order is finalised.
Compare fixed-back seats by support and mounting route
The Cobra Monaco Pro is a fixed-back steel-frame candidate with listed base and side mounting choices. Try the cushion and support with the driver. Confirm the actual version and selected lower arrangement together.
The standard Sparco Sprint card uses the BRR0003 family reference; its maker catalogue shows base and side fixing routes.
The OMP TRS-E Velour is another steel-frame choice with both routes listed. Compare bolster access and the position you want in the Celica before choosing the finish. Garreth would put the driver’s support and entry first in that comparison.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Try reclining choices with their controls and lower fittings
The Sparco R100 is a base-mounted reclining option to try. The shop record linked here uses legacy 00961NR, while the newer catalogue names the 009014 family. Confirm the actual supplied version before choosing fittings from its drawing.
The Corbeau Sportline RRS card is a pair of seats on the listed standard base. Each physical position needs its own Celica bracket and upper assembly. Confirm the package contents and quantities for the complete order.
The Cobra Misano Anniversary has its own reclining mechanism, shell and trim choices. Trial the controls and backrest movement beside the actual door and tunnel. Include any access needed behind the front seats in that trial.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Match the Cobra runner to both connections
The Cobra Premium runner listing offers 291mm and 405mm handle-width options. Match the actual runner to the seat and supplied SB191 slider pattern. The handle label alone cannot identify the complete fixing layout.
Send the full Monaco or Misano reference with the runner enquiry.
Check the upper seat connection and lower bracket connection as separate interfaces. Trial the required movement and release-handle access in the Celica. Include the runner’s thickness when comparing the complete driving position.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Specify the Sparco slider with the actual seat version
The Sparco 0049306 runner is a sliding option to discuss with the named Sparco seats. Its catalogue shows a 271mm longitudinal fixing distance. Confirm the entire upper and lower layout with the supplied seat, supports where used and SB191 bracket version.
The named Sprint and R100-family seat-side base fastenings below are 345mm by 271mm.
Trial both rails through the travel required by the driver and check that they release and lock together. Include the handle and surrounding trim throughout that movement. A shared dimension at one connection leaves the other interfaces to verify.
Use supports specified for the chosen side-mounted shell
For a side-mounted shell, supports join the seat’s side fixings to the lower assembly. The Sparco steel supports shown here are a candidate for the exact Sparco shell and its instructions. Use another seat family’s own confirmed support combination.
The shell’s side fixings and the support’s lower pattern each need their own reference.
Cameron would check the exact shell, support orientation and specified fasteners before comparing the lower connection. Include any runner and the supplied SB191 version in that drawing comparison. The vehicle application alone cannot specify those upper components.
Plan fixed positioning as its own complete arrangement
Planted publishes separate installation arrangements for base-mounted and side-mounted seats, with and without sliders. Its FAQ describes its own side mounts with sliders beneath them. Ask us to specify the complete fixed arrangement if adjustment is not required.
Removing a runner changes the connection and finished position.
Trial the selected components in the actual car using the relevant instructions. Check pedal and steering reach with the driver. Garreth would also try getting over the bolster and the access needed behind the seat.
See the named Sparco seat-side centres at one scale
The named Sprint and R100-family lower fastenings in the Sparco catalogue measure 345mm across and 271mm front to rear. Both dimensions use the same scale in the drawing. Confirm the exact supplied seat version before choosing components around those centres.
The Celica floor, full SB191 slot layout and outside shell dimensions need separate measurements.
Trial the preferred seat and complete lower assembly in the cabin. Include shoulder room and access to the controls beside the actual trim. A Cobra, Corbeau or OMP choice needs that exact version’s drawing for its own seat connection.
Source: Sparco 2025 manufacturer catalogue, printed pages 178 and 326 to 327. The shop’s R100 reference needs supplied-version matching.
Choose the restraint with the shell and actual anchors
Include the intended belt arrangement before the lower fittings are finalised. Match the exact shell and restraint instructions to the actual anchors and driver. Photograph the existing buckle connection and retained hardware.
For a harness enquiry, show any proposed bar or cage and its specified attachments.
Check the shell openings, strap configuration and anchors as one arrangement. Trial routing and buckle access with the seat in its intended position. Choose a harness product once that configuration has been established.
- Original belt: check the exact shell, buckle position and retained mounting hardware.
- Harness: confirm the required straps, shell openings and available anchor arrangement together.
- Two seats: specify each physical side, quantities and the adjustment needed by each occupant.
Send the chassis details with photographs of the present fittings
Send the original chassis identification, build, body and steering side. Include photographs of the mounts and any adapters or floor changes. Keep the exact seat, bracket and runner references together in the enquiry.
Describe the adjustment, access, retained functions and belt arrangement wanted in the finished car.
If the aim is a lower position, measure the present one and trial the complete proposed assembly. The cushion and shell angle contribute alongside the lower fittings. Cameron would check reach and clearances with the actual driver.
Common questions
Which Celica application does SB191 name?
Planted names Toyota Celica fourth-generation T160, 1985 to 1989, excluding All-Trac. Confirm the original chassis, build, actual body and floor. Include any previous changes before selecting the supplied bracket.
How should I enquire about an All-Trac or GT-Four?
Send the exact chassis and build with photographs of the original mounts. SB191’s named manufacturer application excludes All-Trac. Ask for the application for the actual car before choosing fittings.
Can I use the later ST185 guide for this T160?
Use the guide for the actual chassis and its named bracket application. The later ST185 has a separate guide and fitting references. A shared model name or proposed seat does not establish interchangeable floor brackets.
Which body and market details should I send?
Include the actual body, build, market and steering side alongside the original chassis identification. Photograph the mounting locations and any changes. Confirm the supplied manufacturer application for that complete set of details.
Which code is physical left or right?
SB191DR identifies physical left and SB191PA physical right in the maker records. Cobra-prefixed alternate codes retain those positions. Match the full supplied shop reference to the actual steering side.
How do Standard and Alternate runner patterns differ?
Planted’s general FAQ directs wide Cobra and Scheel-Mann runners to the Alternate pattern and includes narrow Cobra runner fixings on both. Send the complete seat and runner references. Confirm the supplied SB191 version and both fixing interfaces.
Does the RRS pair include two Celica brackets?
The linked card describes a pair of seats on the named standard base. Specify a vehicle bracket and selected upper assembly for each physical side separately. Confirm current contents and quantities before ordering.
Can I specify a fixed seat position?
Ask us to specify the full fixed arrangement for the exact seat and car. Planted publishes separate installation arrangements with and without sliders. Check the connections and final position for the chosen assembly.
What does the scaled 345mm by 271mm drawing show?
It shows named Sparco seat-side lower fastening centres in the maker catalogue. The actual Celica floor and full SB191 slot layout need separate references. Match the supplied seat version and each remaining interface.
What if the original mounts have been changed?
Photograph the original locations and current adapters or floor alterations. Include the previous component references where known. Check the named application against the floor and assembly the car actually has.
How much lower will the replacement seat sit?
Compare the current position with a trial of the complete proposed assembly and actual driver. The cushion, shell angle and lower components all contribute. The bracket code alone cannot predict a reduction.
What completes the seat and fitting enquiry?
Send the chassis identification, body, build, steering side and mounting photographs. Include the exact seat and fitting references, access and adjustment wanted, retained functions and belt arrangement. Show any previous adaptations.
Garreth’s top tip
Garreth would try the seat support and bolster access with the driver before choosing a finish. Include any access needed behind the front seats. Keep the complete lower arrangement on the parts list for that exact seat.
Cameron’s fitting view
Cameron would start with the original T160 identity and present floor photographs alongside the SB191 application, excluding All-Trac. Match the physical side and supplied pattern before choosing the upper fittings. Trial the complete position and access with the driver.
Plan your Toyota Celica T160 1985 to 1989, excluding All-Trac seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Sources: Planted application records, slider-pattern and market guidance and assembly-specific instructions; Sparco 2025 catalogue, printed pages 178 and 326 to 327; linked shop listings. Confirm the current supplied versions and actual car before completing the package.







