Toyota Celica 1970 to 1977 Bucket Seat and Fitting Guide
Start with the 1970 to 1977 application and the floor you have
For a Celica in Planted’s 1970 to 1977 application, our listed floor-bracket route is SB197. Bring the actual body and mounting details into the seat enquiry. The right support, adjustment and access matter alongside the finish you want.
Garreth would try the seat’s cushion and bolster before settling on a trim. Cameron would compare the original mounting locations with the car’s current floor. Include any earlier bracket or seat conversion in that conversation.
At a glance
- The SB197 manufacturer application names Toyota Celica, 1970 to 1977.
- SB197DR identifies physical left and SB197PA physical right; confirm the supplied variation against the actual steering side.
- Body and build identification, original mounts and any floor alterations belong in the fitting enquiry.
- Later Celica applications have separate references; keep the generation with the parts list.
- Specify the complete bracket, runner or fixed connection and shell-support arrangement for each seat position.
- The scaled 345mm by 271mm Sparco drawing describes named seat-side centres, separate from the Celica floor.
Identify the actual Celica and its original mounting locations
Planted’s application records name Toyota Celica 1970 to 1977 for SB197. Send the chassis identification, body and build details with the enquiry. Include the steering side and the original seating arrangement.
Photograph the current seat connections and the original mounting locations.
If the car has had floor or seat-mounting work, show those changes as well. The assembly needs checking against the floor that is present now. Cameron would resolve that comparison before choosing the supplied fittings.
Keep each Celica generation with its own application
Our catalogue names SB171 for the 1978 to 1981 Celica application. That is a separate reference from SB197. A Celica model name on its own is not enough to choose between them.
The ST185, T200 and T230 guides below cover later named generations.
Give us the actual chassis and build details if the car’s identity or earlier alterations are uncertain. Use those details for a separate application check. A similar seat or a cage listing cannot establish the floor-bracket fit.
Later-generation guides: Celica ST185 · Celica T200 · Celica T230.
Match the SB197 physical side and supplied version
The listed SB197 is the floor-bracket route for the maker’s named 1970 to 1977 application. Manufacturer codes SB197DR and SB197PA identify physical left and right respectively. Keep the full reference with the position being changed.
The shop’s RHD driver and passenger wording needs matching to the actual steering side and supplied variation code.
The bracket provides one connection in the replacement assembly. Specify the upper fittings and retained buckle hardware alongside it. For two seats, check the physical positions, selected components and quantities separately.
| Physical position | Manufacturer reference | Cobra alternate reference |
|---|---|---|
| Left | SB197DR | COBRA-SB197DR |
| Right | SB197PA | COBRA-SB197PA |
-
From £222.60 Incl. VATFrom £185.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Confirm the runner pattern before choosing the upper fittings
Planted publishes Standard and Alternate slider-pattern choices. Its general FAQ directs wide Cobra and Scheel-Mann runners to the Alternate pattern. Narrow Cobra runner fixings are included on both versions.
The SB197 application records include Cobra-prefixed alternate references for each physical side.
Send the exact seat and runner references when selecting the supplied bracket version. Compare the seat-to-runner and runner-to-bracket connections independently. Cameron would check that complete arrangement before the order is finalised.
Compare fixed-back seats by support and mounting route
The Cobra Monaco Pro is a fixed-back steel-frame option with listed base and side mounting choices. Try the cushion and bolster access with the driver. Choose the exact version and lower arrangement together.
The standard Sparco Sprint card uses the BRR0003 family reference, with base and side fixing routes in the maker catalogue.
The OMP TRS-E Velour is another steel-frame candidate with both routes listed. Compare support, entry and the way the car is used before deciding on the finish. Garreth would keep the driver’s comfort and required access in that choice.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Try reclining choices with their controls and lower fittings
The Sparco R100 gives you a base-mounted reclining choice to discuss. Our linked shop record uses legacy 00961NR, while the newer catalogue names the 009014 family. Match the actual supplied version before choosing fittings from its drawing.
The Corbeau Sportline RRS card is a pair on the listed standard base. Each physical position still needs its own Celica bracket and selected upper assembly. Confirm the package contents and quantities as a complete order.
The Cobra Misano Anniversary has its own reclining mechanism, shell and trim options. Trial the controls and backrest movement beside the actual tunnel and door. Include any access needed behind the front seats in that trial.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Match the Cobra runner to both connections
The Cobra Premium runner listing offers 291mm and 405mm handle-width options. Match the actual runner to the seat and supplied SB197 slider pattern. The handle label alone cannot identify the complete fixing layout.
Send the full Monaco or Misano reference with the runner enquiry.
Check the upper seat connection and lower bracket connection as separate interfaces. Trial the required movement and release-handle access in the Celica. Include the runner’s thickness when comparing the complete driving position.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Specify the Sparco slider with the actual seat version
The Sparco 0049306 runner is a sliding option to discuss with the named Sparco seats. Its catalogue shows a 271mm longitudinal fixing distance. Confirm the entire upper and lower layout with the supplied seat, supports where used and SB197 bracket version.
The named Sprint and R100-family seat-side base fastenings below are 345mm by 271mm.
Trial both rails through the travel required by the driver and check that they release and lock together. Include the handle and surrounding trim throughout that movement. A shared dimension at one connection leaves the other interfaces to verify.
Use supports specified for the chosen side-mounted shell
For a side-mounted shell, supports join the seat’s side fixings to the lower assembly. The Sparco steel supports shown here are a candidate for the exact Sparco shell and its instructions. Use another seat family’s own confirmed support combination.
The shell’s side fixings and the support’s lower pattern each need their own reference.
Cameron would check the exact shell, support orientation and specified fasteners before comparing the lower connection. Include any runner and the supplied SB197 version in that drawing comparison. The vehicle application alone cannot specify those upper components.
Plan fixed positioning as its own complete arrangement
Planted publishes installation arrangements for base-mounted and side-mounted seats, with and without sliders. Its FAQ describes its own side mounts around an arrangement using sliders below them. A fixed assembly needs its own connection and position check.
Ask us to specify the complete fixed arrangement before ordering if sliding adjustment is not required.
Trial the proposed components in the actual car using their relevant instructions. Check pedal and steering reach with the driver. Garreth would also try getting over the bolster and any access required behind the seat.
See the named Sparco seat-side centres at one scale
The named Sprint and R100-family lower fastenings in the Sparco catalogue measure 345mm across and 271mm front to rear. Both dimensions use the same scale in the drawing. Confirm the exact supplied seat version before choosing components around those centres.
The Celica floor, full SB197 slot layout and outside shell dimensions need separate measurements.
Trial the preferred seat and complete lower assembly in the cabin. Include shoulder room and access to the controls beside the actual trim. A Cobra, Corbeau or OMP choice needs that exact version’s drawing for its own seat connection.
Source: Sparco 2025 manufacturer catalogue, printed pages 178 and 326 to 327. The shop’s R100 reference needs supplied-version matching.
Choose the restraint with the shell and actual anchors
Include the intended belt arrangement before the lower fittings are finalised. Match the exact shell and restraint instructions to the actual anchors and driver. Photograph the existing buckle connection and retained hardware.
For a harness enquiry, show any proposed bar or cage and its specified attachments.
Check the shell openings, strap configuration and anchors as one arrangement. Trial routing and buckle access with the seat in its intended position. Choose a harness product once that configuration has been established.
- Original belt: check the exact shell, buckle position and retained mounting hardware.
- Harness: confirm the required straps, shell openings and available anchor arrangement together.
- Two seats: specify each physical side, quantities and the adjustment needed by each occupant.
Send the actual car and a complete assembly enquiry
Send the chassis identification, body, build and steering side with photographs of the original floor mounts. Show current adapters and any earlier alterations. Include the full seat, runner or fixed-connection and support references.
Tell us which access, adjustment, original functions and belt arrangement you want to retain.
Measure the present driving position if changing the height is the aim. The cushion, shell angle and fittings below the seat all affect that result. Cameron would trial the complete proposed position with the driver before confirming reach and clearance.
Common questions
Which Celica application is named for SB197?
Planted names Toyota Celica 1970 to 1977. Match the actual body, build and original floor to that stated application. Include any previous mounting changes when confirming the supplied bracket.
Can I choose the bracket using the Celica model name alone?
Keep the actual chassis and build details with the enquiry. The catalogue names a separate SB171 application for 1978 to 1981, and later Celicas have their own guides. A shared model name does not establish the same floor connection.
Do chassis names on a cage listing establish the seat-bracket fit?
Use the exact floor-bracket manufacturer application and actual mounting locations for the seat enquiry. A cage listing describes a different component. Confirm the body and build details separately.
Which code is physical left or right?
The maker identifies SB197DR as physical left and SB197PA as physical right. Cobra-prefixed alternate codes retain those positions. Confirm the actual steering side and full supplied shop variation code.
What if the car has had floor or mounting work?
Send photographs of the original mounting locations and present adapters or alterations. Include the previous parts references where known. Check the named application against the floor and assembly the car actually has.
How do Standard and Alternate runner patterns differ?
Planted’s general FAQ directs wide Cobra and Scheel-Mann runners to the Alternate pattern and includes narrow Cobra runner fixings on both. Send the complete seat and runner references. Confirm the supplied SB197 version and both fixing interfaces.
Does the RRS pair include two Celica brackets?
The linked card describes a pair of seats on the named standard base. Specify a vehicle bracket and selected upper assembly for each physical position separately. Confirm current contents and quantities before ordering.
Can I specify a fixed seat position?
Ask us to specify the complete fixed assembly for the exact shell and car. Planted publishes separate arrangements with and without sliders. The connections and finished position need checking for the chosen assembly.
What does the scaled 345mm by 271mm drawing show?
It shows named Sparco seat-side lower fastening centres from the manufacturer catalogue. The actual Celica floor and full SB197 layout need their own references. Match the supplied seat version and each remaining connection.
How do I compare entry and access behind the seat?
Try the bolster and any required backrest movement with the complete assembly in the car. Include the controls and surrounding trim in that trial. Describe the access you need before selecting the shell.
How much lower will the replacement sit?
Compare the present position with a trial of the proposed complete assembly and actual driver. The cushion, shell angle and lower fittings all contribute. The floor-bracket code alone cannot predict a reduction.
What information completes the fitting enquiry?
Send the chassis identification, body, build, steering side and mounting photographs. Include the exact seat and fitting references, access and adjustment wanted, retained functions and intended belt arrangement. Show previous adaptations.
Garreth’s top tip
Garreth would choose the seat’s support, cushion and entry before deciding on its finish. Include how the Celica is used and any access needed behind the front seats. Specify the complete lower arrangement around that exact seat.
Cameron’s fitting view
Cameron would match the actual body, build and original floor photographs to the supplied SB197 reference. Confirm the physical side and runner pattern before choosing the upper connections. Trial the full position and access with the driver.
Plan your Toyota Celica 1970 to 1977 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Sources: Planted application records, slider-pattern and market guidance and assembly-specific instructions; Sparco 2025 catalogue, printed pages 178 and 326 to 327; linked shop listings. Confirm the current supplied versions and actual car before completing the package.







