Call Garreth, Cameron & Jack: 0115 647 8650

FREE UK shipping on orders over £100.00 & FREE gifts on checkout

Your garage NewAdd your car and see the parts that fit
Useful Links
Your Account

Talk to us

Garreth, Cameron & Jack · Mon to Fri
Call 0115 647 8650Free advice on your build
Thanks, that’s with us. We reply the same working day.
That didn’t send. Please give us a call instead.

Useful Links

Quick Access

Want to chat?

Call Garreth, Cameron, Jack
Today On: 0115 647 8650
Click Here For Our Contact Form

 

 

Which FIA Race Seat Fits A Spaceframe Lotus Esprit Silhouette? Tillett B6 And B7 Clearance Explained

A customer building a spaceframe Lotus Esprit Silhouette around a Tillett B4 asked us which FIA seat would recline further, mount lower or be shallower. Tillett publish a dimension sheet for the B6 Screamer, the B6 XL, the B7 and the B7 XL, so this time we can give you figures: height, length, widths, bolt spacing and the gap under the shell. They are drawn to scale below. We hold no sheet for the B4, so the last step is a tape measure in your car.

  • Every figure comes from Tillett's own dimension sheets
  • Both shells are listed FIA 8855-1999
  • Product links go to the live listings
A carbon Tillett B6 XL Screamer seat in its protective bag in front of a row of bucket seats in the SportSeats4u showroom
The carbon Tillett B6 XL Screamer in our showroom.
The short answer

Start with the B6 Screamer in the 40cm edges-off cut, on side mounts

On Tillett's sheets the B6 and the B7 share one envelope: 69.5cm front to back, 81cm to 81.5cm tall, a 10cm front lip and 29cm between the bolt centres. The B7 is the lighter seat at 3.8kg. It takes the same space in the car.

  • FIA 8855-1999 in both the 40cm edges-off and 44cm edges-on cuts
  • 40cm is the narrowest outer width in the range, with 34cm inside across the base
  • The shell sits 38mm to 42mm above its mounting frame, so the mounts decide how low it goes
  • Side mounts give a small angle range through the bolt holes, which is where extra recline comes from
81cmOverall height, B6 Screamer (B7 reads 81.5cm)
69.5cmFront to back, B6 and B7
34cmInside width across the base, B6 Screamer
40cmNarrowest outer width, rolled edges cut off

What Tillett's dimension sheets tell us

The customer's car is a spaceframe Esprit Silhouette with a Tillett B4 in it. He wants an FIA seat that sits lower, leans back further or is shallower from back to front. On depth, the sheets are clear: the B6 Screamer and the B7 are both 69.5cm from the front lip to the back of the shell, so neither is a shorter seat.

The back angle is moulded in, so what changes how the seat sits is the mounting, covered further down. We hold no dimension sheet for the B4, which means the comparison with the seat in the car comes from a tape measure.

This page covers the FIA race shells. Our older guide, Which Reclining Sport Seats Fit My Lotus Esprit?, covers the road-style reclining seats that sit alongside them.

Cameron's first requestSend me the B4's width across the shell, its depth from the back to the front edge, and the height of its base above the floor, and I'll set them against these sheets before you order anything. If you'd rather talk it through, drop us an email or click to open a chat.

B6 Screamer and B7: one envelope, one drawing

Both seats are FIA 8855-1999, both are side mount only, and Tillett's sheets give them the same overall length, the same 10cm front lip and the same 29cm between the bolt centres. The height reads 81cm on the B6 and 81.5cm on the B7. The second height Tillett mark on the back reads 54cm on the B6 and 52cm on the B7.

Where they part is weight and construction. The B7 is carbon epoxy at 3.8kg and the Screamer runs from 5.8kg to 6.1kg depending on finish. Tillett's own B7 page sends a wide, edges-off buyer to the B6 XL Screamer, which tells you how close the shapes are. For a car where the question is how much room the seat takes, the drawing below applies to both.

Mounting frame10 cm54 cm81 cm69.5 cm front to back29 cm25 cm42 mm100 cm60°5° leanFront lipSeat back
Tillett B6 Screamer, side view, drawn to scale from the figures on Tillett's dimension sheet. The outline is a schematic, not a trace of the shell. The B7 sheet gives the same 69.5cm length, 10cm front lip and 29cm bolt spacing.
DimensionB6 ScreamerB6 XLB7B7 XL
Overall height81cm81cm81.5cm81cm
Front to back69.5cm69.5cm69.5cm69.5cm
Front lip to top of back (diagonal)100cm100cm100cm100cm
Second height marked on the back54cm54cm52cm54.5cm
Front lip height10cm10cm10cm10cm
Outer width, edges on44cm47cm44cm47cm
Outer width, edges cut off40cm43cm40cmNot printed
Inside width34cm37cm37cm upper, 34cm base37cm
Width across the moulding at the base35cm38cm36cm38cm
Width across the bolt centres or fixing points36cm39cm37cm39cm
Bolt spacing, front to rear29cm29cm29cm29cm
Gap between dome and mounting frame42mm38mm38mm40mm
Back angle as drawn60°60°60°62°
Lean at the top of the back5°5°5°7°

All figures are as printed on Tillett's 2022 dimension sheets. The B7 weighs 3.8kg and the Screamer 5.8kg to 6.1kg.

Standard width or XL, edges on or off

Width is the other figure that decides a spaceframe fit. Tillett give each seat two outer widths: edges on (44cm on the standard shell, 47cm on the XL) and the cut with the rolled edge removed beside the leg (40cm and 43cm). The inside of the shell is the same either way, 34cm across the base on the Screamer and 37cm on the XL.

For a tight spaceframe cockpit we would start with the 40cm cut and check the fit from there. Tillett suggest edges on where the space allows, because the seat is easier to get in and out of.

B6 Screamer44 cm edges on40 cm edges cut off34 cm internalB6 XL Screamer47 cm edges on43 cm edges cut off37 cm internalB744 cm edges on40 cm edges cut off37 cm internal, upper body34 cm internal, baseB7 XL47 cm edges on37 cm internal10 cm scale
Outer and inner widths of the four shells, centred and drawn to the same scale from Tillett's dimension sheets. The B7 sheet marks two inside widths: 37cm in the upper body and 34cm across the base.

The standard B6 in the store is Road and Track approved and is not FIA homologated, so the Screamer is the FIA version. Tillett list a B7 XL for drivers generally over 100kg, and the wide, edges-off B7 is not homologated, which is why Tillett point to the B6 XL Screamer for that cut.

Mounting height and the bolt pattern

With the recline moulded in, the mounts are where height and angle get decided. Tillett give the gap between the dome on the underside of the shell and the mounting frame when the base is set parallel: 42mm on the B6 Screamer, 38mm on the B6 XL and the B7, and 40mm on the B7 XL. The frame then sits above the floor on whatever brackets you choose.

Our STBI listing says side mounting generally gets you lower than bottom mounting and gives some choice over seat angle, with most side mounts allowing a small range through multiple bolt holes. Check the angle at the wheel and at the helmet as well as at the seat base, because a degree or two at the base shows up at the head. Tillett's sheets add that their brackets sit 2° from vertical to match the side of the seat, and a bracket that does not match that angle stresses the composite.

Front lipBack36 cm bolt centres29 cm front to rear15.5 cm25 cmSide mount bolt pattern
Plan view of the side mount bolt pattern, drawn to scale against the 44cm by 69.5cm outline of a B6 Screamer with its edges on. The across-bolt width is 36cm on the B6 Screamer, 37cm on the B7 and 39cm on the XL shells. Front-to-rear spacing is 29cm on all four.

The STBI is a 5 mm aluminium bracket that sits inward, under the shell. That keeps the footprint narrow, which is useful beside a tunnel. Tillett’s own compatibility list names the B6 Screamer and B7 among the seats it takes. Our Tillett seat and bracket compatibility guide sets out the inward and outward options.

The listing says to check the bolt spacing on your shell and keep both sides even, so the bolts clear the shell and the harness slots.

  • From £139.20 inc VAT
  • Aluminium, inward under the shell
  • Listed FIA Approved and MSA Approved
  • Side mount, bolts to the seat and connects to a frame or floor

Product cards show prices excluding VAT. Prices in the text include VAT.

The TLPK1 is Tillett’s low profile fitting kit, for cars where headroom is restricted and a standard mounting height will not work. It gives a lower mounting path and reduces the overall height of the installation, which is the problem in lower GT and sports cars.

The listing is clear that it is an accessory and works alongside a standard Tillett fitting frame and bracket set. Tillett publish little more than the part number and purpose, so send us the seat and frame you plan to use and we will confirm it before you order.

  • £76.06 inc VAT
  • Lowers the installed height
  • Used with a Tillett fitting frame and bracket set
Your B4 mounts may not carry overThe TB4 Extra Tall side mounts list the B1 Carbon, B2 and B4 as compatible seats. They add height, which is the opposite of what you want here, so plan on a fresh set of mounts for a B6 or B7.

Four measurements to take in the car

1

Tunnel to sill

The width the seat has to fit between, measured at the height of the seat base and again at hip height. Set it against 40cm, 43cm, 44cm or 47cm.

2

Depth

Back to front of the seat position, with the driver's legs to the pedals. Set it against the 69.5cm on Tillett's sheet.

3

Headroom

Roof or hoop to the driver's helmet in the seated position, as this decides whether you need the low profile kit.

4

The B4 itself

Width, depth and base height of the seat that is in there now, so we have something real to compare.

Common questions

It is 69.5cm front to back, 81cm tall, 40cm wide with the edges cut off and 34cm wide inside. Send us the B4's width, depth and base height and Cameron will set them against those figures and tell you what he sees.

Not by anything you would notice. The B7 sheet gives a 38mm gap under the shell against 42mm on the Screamer, and 81.5cm overall height against 81cm. Length, front lip and bolt spacing match. What the B7 changes is weight, at 3.8kg.

The XL gives 3cm more inside width (37cm against 34cm) and the outer width becomes 43cm edges off or 47cm edges on. In a narrow cockpit the standard 40cm cut is the narrowest option. Tillett list the B7 XL for drivers generally over 100kg.

The TB4 listing names the B1 Carbon, B2 and B4 only. Tillett's list for the STBI and its sister brackets names the B6 Screamer and B7. We would plan on new mounts, and we can confirm the exact bracket for your shell.

The back angle is moulded into the shell. A small range of seat angle comes from the bolt holes on a side mount, as the STBI listing says. For road-style reclining seats, read our Esprit reclining seat guide.

The standard B6 in the store is Road and Track approved and is not FIA homologated, so this page covers the Screamer and the B7.

Tillett's 2022 dimension sheets for the B6 Screamer, B6 XL, B7 and B7 XL. Where a sheet does not print a figure, we leave it out.

What we would buy

G

Garreth

Garreth's top tip

For this build I'd buy the B6 Screamer GRP in the 40cm edges-off cut. It has the FIA approval, it's the narrowest of the four, and Tillett's sheet gives you every figure to check it against the car before anything is ordered.

The B7 earns its place on weight. At 3.8kg it takes roughly 2kg off the seat, and it sits in the same space as the Screamer.

C

Cameron

Cameron's fitting view

What I like about these sheets is how complete they are. Length, height, front lip, bolt spacing and the gap under the shell are all printed, so I can lay them over your B4 measurements.

Get me the B4's width, depth and base height and the headroom figure. Then we can say whether the STBI on its own gets you low enough or whether the TLPK1 belongs in the plan.

Want us to check a Tillett shell against your Esprit?

Give us the B4 measurements, your headroom and your width between tunnel and sill. Cally, our digital receptionist, takes your details, and Cameron comes back to you with a fit view before you order.

Free UK Shipping

On all orders above £100

Showroom

Try before you buy, by appointment

Delivery Tracking

Updates by email and text