Ford Ka Mk1 bucket seat guide
First-generation Ka, October 1996 to 2008: choose the complete seat assembly
The first-generation Ka has current Sparco and Corbeau fitting options in this guide. The Sparco order includes a bridge piece for the raised floor section; choose the compatible runners and supports with the exact seat.
Use the October 1996 to 2008 first-generation hatchback application as the starting point. Send Garreth the build details for a SportKa enquiry or any car with altered mounting areas. This guide does not establish StreetKa convertible, second-generation RU8 or Ka+ fitment.
Cameron can compare the assembled driving position with the cabin dimensions before you order. Check seat width and the height added by the lower parts in this small cabin.
- Two current first-generation fitting listings are covered: Sparco and Corbeau.
- Sparco 00499069DX is the shop RHD driver choice; 00499069SX is the passenger choice, with one frame per selected position.
- The current Sparco Ka listing includes its raised-floor bridge piece; confirm the actual supplied assembly and hardware.
- The Corbeau order requires a driver or passenger selection; covering both positions does not make one order a pair.
- RECARO 87.04.15 and 87.04.25 refer to the later RU8 Ka in the maker table and are not established Mk1 fitting options.
- Choose cage sections and harness attachments for the actual car and event; EnduroKA has a separate cage ordering restriction.
Mounting
The lower frame connects to the car and the upper parts connect to the seat. Have the mounting areas checked, including previous repairs, and compare the complete fixing arrangement with the supplied hardware.
Cameron can help assess door and console clearance with the driver seated. Check steering position and control operation at the same time, and plan rear access in the three-door hatchback. The final height depends on the frame, rails and any side supports.
Sparco handed frame and bridge piece
The Sparco frame is listed for the Ka Mk1 from October 1996 to 2008. Each order covers one selected position: 00499069DX-1698 for the RHD driver or 00499069SX-1698 for the passenger.
The current listing says that the top-hat bridge piece for the raised floor section is included. A dated Sparco application table also identifies a separate Ka adaptor reference, so have the actual current package confirmed before buying additional bridge parts. This is a Sparco package statement, not a requirement to apply to every manufacturer.
The listed upper base pattern is 345 x 271 mm. Match the seat and any runners to the full fixing arrangement, using the specified mounting method. Garreth can compare the exact seat version with the supplied kit; a matching width alone is insufficient.
-
From £131.77 Incl. VATFrom £109.81 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Corbeau base-seat frame and position choice
Corbeau FORDKA is the brand-specific option for the original Ka. Select Drivers Side or Passenger Side under Sport Seat Position for the single-position order.
The listing describes attachment to the standard floor points and a Corbeau base-mounted seat interface. Corbeau’s general vehicle-subframe guidance concerns compatible base-mounted reclining and classic seats and excludes side-mounted shells. Do not pair this frame with a Sprint X or Revenge X shell simply because the seat is Corbeau.
Corbeau’s general guidance describes double-locking runners, but the Ka listing does not separately itemise every supplied rail or adaptor. Confirm the actual Ka package before ordering extra runners. Garreth can check the seat model and seating side with that enquiry.
Sliding runners and package contents
Sparco 0049306, Cobra Premium SUBFR07EL and Endurance runners are options to assess with the chosen lower assembly and seat. Compare both interfaces and the added height. The Cobra runner has handle-width choices, so specify the actual seat and rail arrangement.
Check the vehicle kit contents and the seat maker’s permitted mounting method before adding rails, including any competition requirements. These runner cards do not establish interchangeability across every frame or shell.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Side supports
The Sparco steel side supports below are an option to assess for a compatible side-mounted shell and lower assembly. Match shell width, fixing positions and hardware together. They do not establish a side-mount route through the Corbeau base-seat frame or approval for the whole installation.
Fixed-back bucket seats
OMP Champ-R and ARS-R, Mirco GT 3D and RS2 3D, and Sparco Evo QRT are side-mounted shell options. Each needs suitable supports and a confirmed connection to the vehicle assembly. Evo QRT is side-mounted, so do not order it as a direct base-mounted seat.
The Corbeau Sprint X System 1 XL and Revenge X System 1 are also side-mounted shells. Their current listings state FIA 8855-1999 approval; System 1 identifies the version and is not a newer approval standard. The Sprint XL provides extra hip width, which does not by itself establish fit for a taller driver.
Check the actual seat dimensions and approval label before committing to the build. Cameron can help compare the driver position and harness openings with the car, alongside the proposed frame and restraint arrangement.
-
From £388.80 Incl. VATFrom £324.00 Excl. VATPayPal Credit250+ coloursKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £425.40 Incl. VATFrom £354.50 Excl. VATPayPal Credit250+ coloursKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £720.00 Incl. VATFrom £600.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £780.00 Incl. VATFrom £650.00 Excl. VATPayPal CreditTop 10 productKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Reclining sport seats
Sparco R100 Martini Racing, R333 and GT are base-mounted recliners with a listed 345 x 271 mm pattern. Assess the actual seat and runner combination against the Sparco package, including travel and rear access at the complete assembly height.
The RECARO Ka frame sold under 870415 is not included here as a Mk1 recommendation. RECARO’s application table places 87.04.15 and 87.04.25 with the later RU8 Ka from February 2009. Ask for an evidenced first-generation lower assembly before choosing a RECARO seat for this car.
-
From £449.47 Incl. VATFrom £374.56 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
£562.10Original price was: £562.10.£505.90Current price is: £505.90. Incl. VAT£468.42Original price was: £468.42.£421.58Current price is: £421.58. Excl. VATPayPal CreditKlarna ReadyAdd to basket
Roll cages
The current Ka cage range includes separate bolt-in assemblies and weld-in kits. Match the exact code and supplied sections to the hatchback, roof and intended use before ordering. A bolt-in description does not guarantee an installation without welding or trimming.
Safety Devices F102 complete and rear-only orders
Safety Devices F102 is listed for the three-door Ka Mk1 hatchback from 1996 to 2008. The full order offers rear single-diagonal or cross-diagonal arrangements, with door-bar choices. The separate rear-cage order supplies the rear section rather than the complete front and rear assembly.
The maker identifies F102 3SMU as the front section, 5SMU or 5SXU as rear options, and DSUO/DSUN as the single door bars. The front requires a rear cage; door bars require the appropriate front and rear assembly. Confirm the selected order and code-specific homologation documents.
For EnduroKA, Safety Devices says the cage must be purchased through the series organiser. Follow that route and the current series requirements before placing a cage order. A normal shop configuration is not proof of series eligibility.
-
From £1,018.80 Incl. VATFrom £849.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £560.40 Incl. VATFrom £467.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
SW full cage and installation work
The SW Ka Mk1 full cage order has colour and rear-cross-gusset choices. Its current shop description specifies welded footplates and dashboard cutting, and excludes cars with a factory sliding sunroof. Arrange a competent installation and confirm the actual supplied cage layout.
The listing describes MSUK compliance by reference to tube dimensions. Confirm the required documents and specific championship rules, together with the engineered harness attachments for the proposed layout.
-
From £1,344.00 Incl. VATFrom £1,120.00 Excl. VATPayPal CreditMade to orderKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Custom Cages multipoint and National kits
Custom Cages FKA/04T T45 and FKA/04C CDS are the multipoint weld-in choices. The current CDS maker page labels FKA/04C FIA Compliant, which differs from a certificated design. Confirm the exact current T45 specification and certification documents rather than transferring the CDS description or a general approval label.
FKA/22NA is the separate six-point National CDS weld-in kit. The maker describes national MSUK compliance and expressly distinguishes it from current FIA International requirements. It includes footplates and profiled tubes for a competent fabricator; assess the exact installation and event requirements.
Sparco and OMP cage packages
Sparco 00713068 is listed for the Ka RBT application from October 1996 to 2008. The shop describes an eight-point Fe45 bolt-in cage with mounting hardware. Confirm the current code-specific documents and supplied kit before using it for competition.
OMP AB/105P/309 is listed for the 1996 to 2008 Ka with A2SX features: single door reinforcements, sleeve connections and a rear-arm diagonal. Its description requires welding of foot brackets and work on connecting or door tubes, and says fitting bolts are not supplied. Have the actual instructions and hardware requirements checked before installation.
Harnesses
Assess the TRS Clubman, TRS Magnum, Takata Drift II and Drift III, and Schroth Profi 3×2 with the exact seat and anchorage arrangement. Strap count alone cannot establish suitable factory points, a cage tube or a harness-bar attachment. Follow the selected belt maker’s instructions for strength, routing and angles.
Cameron can help check the path through the seat and the lap, shoulder and any crotch-strap attachments. Confirm the belt’s actual approval and intended use separately from the seat and cage as part of the complete restraint installation.
-
From £96.00 Incl. VATFrom £80.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £120.00 Incl. VATFrom £100.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £246.00 Incl. VATFrom £205.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £274.80 Incl. VATFrom £229.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £294.00 Incl. VATFrom £245.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £324.00 Incl. VATFrom £270.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £444.01 Incl. VATFrom £370.01 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
What fits
Compare the vehicle application, seat interface and actual package before choosing the parts.
| Route or seat | Application or method | Interface or contents | Check before ordering |
|---|---|---|---|
| Sparco Ka Mk1 | October 1996 to 2008 | 00499069DX RHD driver /SX passenger | One selected-side frame;current listing includes bridge piece |
| Sparco upper interface | 345 x 271 mm base pattern | Seat and runners must match | Actual package,hardware and assembled height |
| Corbeau FORDKA | Original Ka,selected position | Compatible base-mounted seats | Confirm actual runners;not a route for side shells |
| RECARO 87.04.15 /25 | Later RU8 from February 2009 | Not established Mk1 frame fit | Separate generation;do not pair from brand alone |
| Runners and side supports | Separate upper connections | Match both interfaces and hardware | Added height and actual package contents |
| OMP /Mirco /Evo QRT shells | Side mounting | Suitable supports and lower assembly | Seat dimensions,label and actual installation |
| Corbeau System 1 shells | Sprint X XL /Revenge X | FIA 8855-1999 stated | Version not newer standard;XL width not automatic height fit |
| Sparco R100 /R333 /GT | Base-mounted recliners | 345 x 271 mm listed | Actual rails,frame connection,travel and rear access |
| Safety Devices F102 | Full or separate rear order | Single or cross rear diagonal;door-bar choices | Exact assembly/docs;EnduroKA ordering restriction |
| SW Ka Mk1 cage | Colour/rear-cross-gusset choices | Welded footplates,dashboard cutting | No factory sliding sunroof;actual event documents |
| Custom FKA/04T /04C | T45 /CDS multipoint weld-in | CDS maker label FIA Compliant | Exact T45 specification/certification and event acceptance |
| Custom FKA/22NA | National six-point CDS weld-in | National MSUK compliance | Not current FIA International specification |
| Sparco 00713068 | Ka RBT October 1996 to 2008 | Eight-point Fe45 bolt-in shop specification | Exact supplied kit and current documents |
| OMP AB/105P/309 | Ka 1996 to 2008,A2SX | Welding work and bolts separate | Confirm actual installation instructions and hardware |
Manufacturer references: RECARO application table, Corbeau subframe guidance, Safety Devices F102, Custom Cages FKA/04C and FKA/22NA National kit.
Common questions
Which first-generation fitting brands are covered?
The current first-generation frame options covered here are Sparco and Corbeau; match the exact kit to the car and seat.
Which Ka generation does this guide cover?
The starting application is the first-generation hatchback from October 1996 to 2008; confirm SportKa details and do not extend it to StreetKa, RU8 or Ka+ from the badge alone.
Which Sparco part is the RHD driver choice?
The shop lists 00499069DX-1698 for the RHD driver position and 00499069SX-1698 for the passenger position.
Does one Sparco frame order cover both seats?
Each selected-side order covers one seat position, so specify both handed parts when fitting two seats.
Is the Sparco bridge piece included?
The current Sparco Ka listing says it includes the raised-floor top-hat bridge piece; confirm the actual supplied package before buying extra bridge parts.
Does every brand require the same bridge piece?
Use the chosen manufacturer's specified assembly; the bridge statement here describes the Sparco order and does not establish every brand's construction.
What is the listed Sparco base pattern?
The frame listing states 345 x 271 mm, but the actual seat, runners and complete fixing arrangement must also match.
How is the Corbeau seating side chosen?
Its Sport Seat Position order choice selects Drivers Side or Passenger Side for the required position.
Does the Corbeau listing supply a pair?
Its coverage of both sides describes the available position choices; confirm the selected single-position order rather than assuming a pair.
Can the Corbeau frame take any Corbeau shell?
Its route concerns compatible base-mounted seats; Corbeau's general subframe guidance excludes side-mounted shells such as Sprint X and Revenge X.
Should I add runners to the Corbeau order?
Confirm the actual Ka package first; general Corbeau guidance describes double-locking runners, but the Ka listing does not itemise every supplied rail or adaptor.
Does RECARO frame 870415 fit the Mk1?
The maker table places 87.04.15 and 87.04.25 with the later RU8 Ka from February 2009, so this guide does not recommend it as a Mk1 frame.
Are the runner options interchangeable?
Match both runner interfaces, hardware and installed height to the actual frame and seat before ordering.
Can Evo QRT bolt directly to the base?
The listed Evo QRT is side-mounted and needs suitable supports plus a confirmed lower connection.
Is System 1 a newer FIA standard?
It identifies the Corbeau version; the current Sprint X and Revenge X listings state FIA 8855-1999 approval.
Does an XL seat establish fit for a tall driver?
Extra hip width does not establish shoulder fit, harness-opening position or head clearance for the actual driver.
Which recliners are compared here?
The Sparco R100 Martini Racing, R333 and GT are base-mounted options to assess with their actual runner and vehicle-frame assembly.
How does the F102 rear order differ from the full cage?
The rear-only order supplies the rear section; confirm front and door-bar requirements separately for the intended assembly.
Can I order any F102 configuration for EnduroKA?
Safety Devices says cages used in EnduroKA must be purchased through the series organiser, subject to current series requirements.
Does the SW bolt-in cage avoid welding?
The shop description specifies welded footplates and dashboard cutting, so arrange installation using the actual instructions.
Is the SW cage listed for a factory sliding sunroof?
The current listing excludes factory sliding-sunroof cars; confirm the actual roof and cage application.
Is the National CDS cage an international certificated kit?
FKA/22NA is described for national MSUK compliance and distinguished by the maker from current FIA International requirements.
Does the OMP bolt-in cage include fitting bolts?
The AB/105P/309 description says bolts are not supplied and identifies welding work; confirm the instructions and required hardware.
Does strap count establish harness attachment points?
Use the selected harness instructions and an engineered anchorage arrangement; neither strap count nor cage presence establishes suitable attachment points.
More help
Send Garreth the build details, body and roof type, market and physical seating side, with the exact seat model. Say whether the order is for one seat or both, and include the intended event requirements. Cameron can check the proposed frame, upper parts and driving position against that specification.
Call 0115 647 8650 or use the contact link below with the details.
Need a personal recommendation?
We're here to ensure you pick the right seat.
Contact us today.



















