Call Garreth, Cameron & Jack: 0115 647 8650

FREE UK shipping on orders over £100.00 & FREE gifts on checkout

Your garage NewAdd your car and see the parts that fit
Useful Links
Your Account

Talk to us

Garreth, Cameron & Jack · Mon to Fri
Call 0115 647 8650Free advice on your build
Thanks, that’s with us. We reply the same working day.
That didn’t send. Please give us a call instead.

Useful Links

Quick Access

Want to chat?

Call Garreth, Cameron, Jack
Today On: 0115 647 8650
Click Here For Our Contact Form

 

 

How to Install Sparco Reclining Seats with Slider Rails, DIY Fitting Guide

Seat fitting guide

Fitting a pair of Sparco reclining sport seats such as the R100, R333 or R500 is a job many owners do at home. With the right parts and ordinary tools it is straightforward: a frame made for your car, a Sparco sliding runner kit, and the seat, all on the same bolt pattern.

This guide covers the parts you need, how the bolt patterns line up, the fitting steps in order, and what these seats are and are not for. One thing to know first: Sparco's reclining seats are road and track seats, not FIA approved, so they are not for competition.

  • Sparco R100, R333 and R500 recliners are base mount seats on a 345mm by 271mm pattern
  • Sparco's sliding runner kit uses the same 345mm by 271mm pattern
  • You also need a frame made for your car, or a suitable adaption
  • Order runners once per seat; the twin kit covers both seats
  • Tighten every fixing to the torque the frame and runner makers specify
  • Recliners on runners are for road and track days, not FIA competition
Black Sparco R100 vinyl reclining seats with red harnesses fitted in a customer's Audi TT on Sparco frames and runners
Sparco R100 recliners in a customer's Audi TT, fitted on Sparco frames with sliding runners.

What you need

Gather everything before you start:

  • A Sparco reclining seat, such as the R100, R333 or R500
  • A Sparco sliding runner kit, one kit per seat, or the twin kit for a pair
  • A frame made for your car, from Sparco or another maker on the same pattern
  • M8 bolts and washers, if they are not supplied with your parts
  • Tools: a socket set, spanners, hex keys and a torque wrench

Lay the parts out and check you have every fixing before the old seats come out. It saves a car sitting without seats while you wait for a bolt.

How the bolt patterns line up

The whole job depends on three parts sharing one pattern:

  • The seat: Sparco's recliners bolt down on a 345mm by 271mm base pattern, 345mm side to side and 271mm front to back.
  • The runners: Sparco's runner kit uses the same 345mm by 271mm pattern, top and bottom.
  • The frame: a Sparco direct fit frame presents the same pattern for the runners to bolt to.

That same 345mm by 271mm pattern is used by OMP and Corbeau base mount seats too. Recaro seats use a wider 405mm pattern and go on Planted brackets, so they are a different job. Our guide to seat bolt patterns explains the differences.

A Sparco sliding runner kit with its looped release bar being measured across with a tape measure
A Sparco runner kit being measured across in the showroom.

Fitting, step by step

Step 1: fit the runners to the seat. Lay the seat face down on a blanket or soft surface. Place the two runners under the base with the release bar spanning both, so one pull moves both sides together. Line up the holes and fit the M8 bolts and washers loosely.

Step 2: fit the frame to the car. If the frame is not already in, bolt it to the car’s seat mounting points in the floor. Direct fit frames are made to use the factory points, so there should be no drilling.

Step 3: fit the seat and runners to the frame. Lower the seat and runners onto the frame. Slide the seat forward to reach the rear holes and back to reach the front ones, and fit the bolts with large washers.

Step 4: tighten and check. Tighten every bolt evenly, to the torque the frame and runner makers specify. Then sit in the seat, run it through its full travel, and make sure it locks firmly in each position on both sides.

A few things that catch people out:

  • Fit the release bar before the seat goes in; it is much harder afterwards.
  • Do not force a bolt into a hole that does not line up. Check the frame is the right one for your car and side.
  • Keep the factory seat belt buckle in mind. Some frames carry a bracket for it; others expect a harness.
  • If the car had side airbags in its factory seats, plan for that before you start.
A single black Sparco sliding runner with its threaded studs and front mounting tab on a white table
One side of a Sparco runner kit, showing the studs and mounting tab.

If you are fitting to a car where the runners need a different route, such as some MX-5s, our answer on whether Sparco runners bolt straight to the car is worth a read, and our guide to fitting Sparco and Corbeau recliners to an M2 frame covers that frame.

Not for FIA competition

Sparco’s reclining seats are not FIA approved, and a recliner on sliding runners is not a setup for competition. The reclining mechanism and runners are not built to the standard motorsport seats are tested to. They suit:

  • daily drivers and road cars
  • fast road builds and show cars
  • non-competitive track days

If you plan to compete, you need an FIA homologated fixed-back bucket seat on side mounts, fixed to the frame, and your scrutineer will check it. Garreth’s advice is to decide which kind of car you are building before you buy the seat, because it changes every other part.

Choosing the frame

We list direct fit frames for a wide range of cars from Sparco, Corbeau, Cobra and Planted Technology. They bolt to your car’s factory floor mounts and give the seat and runners a proper foundation, with no fabrication. For Sparco recliners, a Sparco frame, or another frame on the 345mm by 271mm pattern, is the simplest route. Cobra frames use a 291mm pattern, so they are not a direct match.

If you are not sure which frame suits your car, send us the make, model and year, and the seats you are fitting, and we will put the full set together.

Sparco’s R100, R333 and R500 are base mount seats on a 345mm by 271mm pattern.

Yes, on base mount seats with the same 345mm by 271mm pattern.

Tighten them evenly to the torque the frame and runner makers specify, using a torque wrench.

No. They are road and track seats, suited to road cars and non-competitive track days.

Yes. One kit covers one seat, or the twin kit covers a pair.

💬
The key partThe Sparco runner kit

Same 345mm by 271mm pattern as the seat and frame, so it all lines up.

Need a personal recommendation?

We're here to ensure you pick the right seat. Contact us today.
Our showroom virtual walk through!
Have a walk around our showroom before you even buy your new seats. 
Our hands on experience, is what allows us to bring you our recommendations.
Free UK Shipping

On all orders above £100

Showroom

Try before you buy, by appointment

Delivery Tracking

Updates by email and text