Datsun / Nissan 720 Pickup (1980-1986) Bucket Seat and Fitting Guide
Choose seats and a complete fitting kit for your 720 pickup
The 720 sits between the earlier Datsun pickups and the later D21 Hardbody. Nissan records the 720’s introduction in 1979; the fitting kit in this guide follows Planted’s named Nissan/Datsun 720 Pickup application of 1980-1986.
Planted SB257 is the listed vehicle bracket. Match it to the actual truck and physical seat position, then specify the seat, runners and any supports above it. Include the cab type and original market when asking for a fitting recommendation.
Try fixed buckets and recliners with the person who will drive the truck. Cab space behind the backrest can limit the position you can use. A useful trial includes getting in and out as well as reaching the pedals.
At a glance
- Named bracket: Planted SB257, Nissan/Datsun 720 Pickup (1980-1986).
- Identify the 720 chassis; the D21 Hardbody is a separate application.
- Standard physical-left reference SB257DR; physical right SB257PA.
- Shop driver/passenger labels refer to right-hand-drive vehicles.
- Confirm Standard or Alternate runner pattern separately from side.
- Cab, drivetrain, floor and any bench conversion need individual checks.
Identify the 720 before choosing the bracket
Send the chassis details with the actual year and original market. State the cab type and whether the truck is two- or four-wheel drive. Nissan’s heritage account records a 4WD addition to the 720 range, but that history does not establish that every floor takes the same seat bracket.
Check a truck near the changeover to the D21 by its identity and mounting arrangement. Nissan identifies the Hardbody as D21, following the 720. A registration year or Nissan badge alone is not enough to select SB257.
Show the floor and the seats being replaced
Photograph the current lower seat assembly and floor attachments before dismantling them. Say whether the truck has a bench, separate seats or a previous conversion. Show any repaired mounts and adapter references to the installer.
A bench-to-bucket conversion needs a complete plan for both proposed seat positions and their restraints. Have the actual attachments checked against the chosen bracket. The general 720 listing does not establish that every bench-equipped cab already has the required separate-seat fittings.
Start the lower assembly with the named SB257 bracket
SB257 is the vehicle-specific adapter below the replacement seat assembly. Confirm the physical side and supplied pattern for the actual truck. Put the seat mounting method beside those references on the quote.
For a base-mounted seat, specify compatible seat-side fittings and runners if adjustment is needed. A side-mounted shell also needs suitable supports. Include the attachment hardware so each connection can be checked before ordering.
-
From £222.60 Incl. VATFrom £185.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Put the physical side beside the full part number
Planted identifies SB257DR as Standard physical left and SB257PA as Standard physical right. The shop labels those choices RHD Passenger Side and RHD Driver Side respectively. Include the actual steering arrangement with the order.
For an LHD truck, physical left is the driver’s position. Confirm the floor arrangement as well as the side. Planted’s general FAQ says that its reference vehicles are LHD unless stated otherwise and that not every RHD or international version has been verified.
| Physical side | Maker Standard | Maker Alternate | Shop label |
|---|---|---|---|
| Left | SB257DR | COBRA-SB257DR | RHD Passenger Side |
| Right | SB257PA | COBRA-SB257PA | RHD Driver Side |
Confirm Standard or Alternate before choosing the runners
Both manufacturer side pages offer Standard and Alternate patterns. Standard includes the Recaro slider pattern; Alternate replaces it with Cobra / Scheel-Mann. Confirm the supplied version independently of the shop’s driver/passenger selection.
Put the exact runner reference on the quote with SB257. Check its lower fixing against the supplied bracket and its upper fixing against the seat or supports. A brand name on a compatibility list does not specify the whole assembly.
Compare fixed buckets for support and access
The Cobra Monaco Pro, Sparco Sprint and OMP TRS-E are fixed-back options to try. Their linked listings describe base and side mounting options. Choose the permitted method for the exact seat version and specify the lower components with it.
Try the seat with the driver in normal driving clothing and any equipment used on track. Check the outer shoulders and lower bolsters against the door and centre tunnel. In the pickup cab, assess the space behind the shell at the position the driver needs.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Compare reclining seats for road use
The Sparco R100, Corbeau Sportline RRS and Cobra Misano Anniversary are base-mounted reclining options to compare with fixed buckets. Try their cushion and backrest support with the driver before choosing trim.
Trial the backrest travel inside the cab, including the adjustment controls and the space needed to use them. If access behind the seat matters, include that movement in the trial. The linked RRS listing supplies two seats; each position needs its own confirmed lower assembly.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Match the exact Cobra runner to the bracket pattern
The linked Cobra Premium runner listing offers 291mm and 405mm handle-type options. Give the exact runner reference and have both attachment interfaces checked. The handle choice alone does not establish all the fixing dimensions.
Planted distinguishes Narrow and Wide Cobra slider patterns. Narrow is included on both bracket versions; Wide calls for Alternate or a separately specified modification. Confirm the supplied components before buying rather than assuming the side selector chooses that pattern.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Specify adjustment with the complete seat assembly
The linked Sparco runner is another adjustment option to assess. Its upper fixing must match the seat or supports and its lower fixing must suit the supplied SB257. Agree both connections with the fitting kit.
Trial the handle where the driver can reach it and check both runners lock correctly through the travel needed. Judge seat height with every lower component assembled. Recheck the backrest clearance at the rearward driving position.
Add supports when the chosen shell uses side mounting
The linked Sparco steel side supports are an option to check against a shell that permits side mounting. Match the shell’s fixing locations, then specify how the supports attach to the runner or bracket.
A direct fixed installation needs its own attachment plan. Planted’s instructions distinguish it from a sliding assembly. Have any required bracket work specified by the installer; removing runners does not establish that the remaining holes line up.
Trial the driving position inside the actual cab
Check pedal reach and visibility with the driver in the complete assembly. Assess headroom beneath the actual roof and trim, using the normal helmet where relevant. Include any structure or equipment fitted near the seat.
Move through the adjustment range the regular drivers need. Check the shell and controls against the door and tunnel, along with buckle access and clearance behind the backrest. Compare the finished position with the original seat rather than assuming SB257 will lower it.
Plan the restraints alongside the seat
Identify where the existing belt and buckle attach and show those fittings to the installer. Check their position and operation with the replacement seat. A bracket tab or a matching seat pattern does not establish the finished restraint arrangement.
For a harness, specify the exact model and intended use before choosing anchors. Have the routing assessed with the seat and cab structure under the relevant instructions. Shell openings do not provide vehicle anchors. If the truck is intended for competition, check the complete installation against the event requirements.
Check the bare bracket before building the seat assembly
Planted’s instructions begin with checking the components and trialling the bare bracket against the vehicle mounts. Build the upper assembly outside the truck, then trial it in position with the driver. Follow the instructions and fastener requirements for the exact supplied parts.
Confirm access and adjustment before final tightening. Keep the agreed driving position while completing the assembly and recheck moving parts afterwards. Have repaired or altered floor attachments assessed before using them for the replacement seat.
Keep the whole fitting plan on one quote
Send the truck details and mounting photographs with the preferred seat. Include existing parts proposed for reuse. We can then work through the bracket choice and upper fittings with you.
- Actual year, 720 chassis details and original market.
- Cab type, drivetrain, steering arrangement and physical seat position.
- Existing bench or separate seats, plus photographs of the floor attachments.
- Chosen seat version and confirmed SB257 side and runner pattern.
- Adjustment and restraint requirements, with event details if applicable.
Common questions
Planted SB257 is listed for Nissan/Datsun 720 Pickup (1980-1986). Match that application to the actual truck and physical seat position, then specify the seat and upper fittings.
Those are the years in the named Planted SB257 application. Nissan records the historical introduction of the 720 in 1979. An introduction date does not automatically extend the bracket application to an earlier truck.
The named SB257 application uses both Nissan and Datsun for the 720 pickup. Identify the actual 720 chassis and configuration when ordering. A badge alone does not establish the mounting arrangement.
The D21 is a separate vehicle application. Identify the truck near a model changeover by its chassis and floor attachments before choosing parts. Do not transfer the 720 bracket recommendation from the registration year alone.
The manufacturer gives a general 720 Pickup application. Supply the exact cab type and original market, then have the present floor attachments compared. The general listing does not establish every cab configuration.
Nissan records a 4WD model within the 720 range, but vehicle history does not prove identical seat mounts. Include the drivetrain with the enquiry and have the actual floor checked against the proposed bracket.
Have both proposed positions and their attachments checked before ordering. Include the existing bench mountings and belt attachments in the photographs. The SB257 name alone does not establish a complete bench-to-bucket conversion.
SB257DR is the manufacturer’s Standard physical-left reference, labelled RHD Passenger Side in the shop. On an LHD truck that physical position is the driver’s side.
SB257PA is the manufacturer’s Standard physical-right reference, labelled RHD Driver Side in the shop. Include the actual steering arrangement with the order.
Have the actual floor checked as well as identifying the physical side. Planted’s general FAQ explains that not every RHD or international configuration has been verified.
Standard includes the Recaro slider pattern. Alternate replaces it with the Cobra/Scheel-Mann pattern. Confirm the supplied version separately from driver or passenger selection.
The shop lists runners as a separate part for adjustment. Ask for the bracket, selected runner and any side supports to be itemised with the attachment hardware.
Give the exact runner reference and check its upper and lower fixing dimensions. The linked handle-type choices alone do not specify every attachment. Planted also distinguishes Narrow and Wide Cobra patterns.
Try the exact seat with the driver and confirm its permitted mounting method. Trial the whole assembly inside the cab, including outer shoulder width and space behind the backrest. A named vehicle frame does not establish shell clearance.
Compare the linked recliners with the driver and specify compatible base fittings. Check backrest travel and adjustment controls inside the actual cab. Include access behind the seat where needed.
Specify suitable supports for a shell using its side fixings and check their lower connection. Sliding and direct fixed assemblies need their own attachment arrangements.
Measure the finished position with the exact seat and all lower components assembled. Include roof trim and normal driving equipment in the trial. No universal height reduction is established for every SB257 combination.
Show the work and existing adapter references to the installer before ordering. Have the present mounting positions and condition assessed against the bracket. Previous seat work needs to be included in the fitting plan.
Have the actual belt and buckle attachments checked with the replacement seat. Confirm routing, access and operation during the trial under the relevant component instructions. A bracket tab does not establish every buckle arrangement.
Specify its exact model and intended use. Have the routing and anchors planned with the seat and cab structure under the relevant instructions. Harness openings in the shell do not provide vehicle anchors.
Have each full part reference and actual mounting arrangement checked for this installation. Shared Nissan or Datsun branding does not establish interchangeable seat fittings between generations.
Send the year, chassis and cab details with mounting photographs and the physical side. Add the preferred seat and adjustment needs, plus the intended restraints and any parts proposed for reuse.
Garreth’s top tip
Garreth would try the seat in the driving position before choosing trim. In a pickup, include the movement needed to get in and out and any access you use behind the backrest. Take the normal driving equipment to the trial.
Cameron’s fitting view
Cameron would keep the cab, drivetrain and original-market details beside the SB257 side reference. Show the existing bench or separate-seat attachments and confirm the supplied runner pattern. That gives the fitting quote the information needed for the actual truck.
Plan your Datsun / Nissan 720 Pickup seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Sources: Planted’s physical-left and physical-right SB257 applications, installation instructions and fitting FAQ; Nissan’s 720 history and D21 identity for vehicle context; and the linked shop listings. Check the current instructions for the exact components supplied.







