Chevrolet Corvette C3 Bucket Seat and Fitting Guide
Compare your C3 floor with the SB267 drawing first
Planted lists the SB267 seat bracket for the Chevrolet Corvette C3, 1968-1982, with a specific floor-pattern warning. Compare the actual mounting holes with Planted’s drawing before choosing the bracket. A C3 model year alone will not confirm that match.
Garreth would start the seat comparison with the driver and the support wanted from the change. Cameron would put photographs and measurements of the existing floor beside the bracket reference. The proposed seat and every lower component can then be checked as one assembly.
At a glance
- Listed application: Chevrolet Corvette C3, 1968-1982, Planted SB267.
- Floor patterns vary; compare the actual holes with Planted’s original drawing.
- Drawing dimensions are approximate and measured between mounting-hole centres.
- Physical-left Standard reference SB267DR; physical-right SB267PA.
- Agree the runner pattern separately from the physical-side choice.
- Trial the complete seat for access, control reach and clearance.
Identify the car and its present mounting points
Give the exact year and original market with the C3 identification. Include its current steering position and the physical side being changed. Show any earlier seat conversion or mounting repair in the photographs.
Planted warns that C3 floor bolt patterns vary. Have the mounting points exposed and identified for a comparison with the bracket drawing. If the holes do not match, Planted says changes to the floor or bracket may be required; have that discrepancy assessed before ordering.
Compare hole centres on the correct side of the drawing
Open Planted’s C3 floor-pattern drawing while measuring. It marks the front and rear of the car and identifies each door. Its Driver / Left and Passenger / Right captions describe physical sides; keep those positions clear if the car’s steering arrangement differs.
On the physical-left pattern the front span is 15-1/2 inches and the rear span is 15-5/8 inches. Both fore-and-aft spans are 19-1/8 inches. The two diagonals are labelled 24-3/4 and 24-1/2 inches; use the original drawing to identify each diagonal.
On the physical-right pattern the front span is 15-1/2 inches and the rear span is 15-3/8 inches. The left edge of that pattern, towards the car’s centre, is 19-1/4 inches; the right-door edge is 19-1/8 inches. Both diagonals are labelled 24-5/8 inches.
Planted calls every measurement approximate and takes it at the centre of the mounting holes. The drawing gives no acceptable mismatch tolerance. Cameron would ask for labelled measurements and clear mounting photographs so a discrepancy can be reviewed before a bracket is specified.
Specify SB267 after the floor comparison
The linked SB267 listing is the vehicle-bracket option to discuss once the actual floor has been compared. Keep the chosen physical side and supplied runner pattern on the quote. Have the bracket’s attachment and the condition of the mounting points assessed with the installer.
Above the vehicle bracket, a base-mounted seat needs its compatible seat-side fittings. A side-mounted shell needs suitable supports. Include runners if adjustment is required and specify the hardware for every connection.
Reconcile the shop label with physical left or right
Planted names SB267DR as physical left and SB267PA as physical right. The shop’s selectable variations label SB267DR RHD Passenger Side and SB267PA RHD Driver Side. Keep the exact reference with the actual position being changed.
On an LHD car, physical left is the driver’s side. Confirm the car’s steering arrangement when requesting the bracket, even though the shop labels that variation RHD Passenger Side. Both physical-side options are selectable in the listing; its driver-only description needs checking against the chosen variation.
There is a separate choice at the runner connection. Standard includes the Recaro slider pattern; Alternate exchanges that pattern for Cobra/Scheel-Mann. Confirm the supplied version with the exact upper assembly.
| Physical side | Standard | Alternate | Shop variation label |
|---|---|---|---|
| Left | SB267DR | COBRA-SB267DR | RHD Passenger Side, SB267DR |
| Right | SB267PA | COBRA-SB267PA | RHD Driver Side, SB267PA |
Try the fixed buckets for support and cabin clearance
The Cobra Monaco Pro, Sparco Sprint and OMP TRS-E are fixed-back options to compare with the driver. Their listings describe base and side mounting options. Confirm the permitted attachment for the exact version being quoted.
Garreth would try the shell’s cushion and backrest support before settling on a model. Trial access over the bolsters as well as the seated position. Check the widest points of the shell against the actual cabin, using the proposed bracket and upper fittings.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Check the recliner mechanism with the seat in position
The Sparco R100, Corbeau Sportline RRS and Cobra Misano Anniversary are base-mounted reclining options to discuss. Garreth would compare the exact seat’s support and backrest adjustment with the driver. Check that the adjustment controls remain usable beside the surrounding trim.
Trial the movement you intend to use, including the runner travel if runners are specified. The linked RRS listing supplies a pair of seats. Each position needs its own floor comparison and confirmed lower assembly.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Confirm the exact Cobra runner and supplied pattern
The Cobra Premium runner listing has 291mm and 405mm handle-type choices. Have the exact runner’s attachment dimensions checked at the bracket and at the seat or supports. Those handle labels alone do not identify the complete bolt pattern.
Planted distinguishes Narrow and Wide Cobra slider patterns. Narrow is included on both bracket versions; Wide needs Alternate or a separately specified modification. Agree the supplied SB267 version before ordering the runner assembly.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Match the Sparco runner at both attachments
The linked Sparco runner is an adjustment option to assess with the chosen seat. Check its lower connection against the supplied bracket pattern and its upper connection against the seat or side supports. Include the required hardware on the parts list.
Trial the handle and locking operation with the whole assembly in the car. Check the travel needed by each regular driver. Compare the final seating height and control reach with all lower components fitted.
Use supports permitted by the exact shell
The linked Sparco steel supports are an option for a shell that permits side mounting. Match their attachment positions to the seat and specify their lower connection to the runner or vehicle bracket. Follow the instructions for those particular components.
For a base-mounted seat, itemise its seat-side fittings separately.
Trial the assembled seat with the actual driver
Place the complete assembly in the car and check the driver’s visibility and reach to the pedals. Try the controls from the intended seated position. Include a helmet or other equipment when it forms part of the intended use.
Check the shell and its lower fittings against the door trim, centre area and any cage through the adjustment range you will use. Try getting in and out. A floor pattern that matches the bracket still leaves the seat’s width, position and movement to be checked in the cabin.
Record the existing restraint attachments
Photograph the actual belt and buckle attachments before removing the old seat. Show the installer any fittings added during an earlier conversion and identify affected seat equipment or connections. Agree the plan for those parts with the proposed seat assembly.
Follow the seat, restraint and fitting instructions for the components being used.
Plan harness routing and anchors with the seat
If a harness is proposed, give its exact model and intended use. Have the routing and anchor positions assessed with the chosen seat and the surrounding structure. Include any cage or other parts involved in that installation.
Harness openings in the shell do not establish suitable anchor points in the car. Use the seat and harness instructions for the complete combination. For competition use, have the finished installation checked against the event’s requirements.
Resolve the floor match before assembling the seat
Start with the C3 floor comparison and have any discrepancy assessed. Once the bracket application and attachment are agreed, Planted’s fitting sequence checks the bracket in the vehicle, assembles the upper parts outside it and trials the complete seat assembly. Follow the current instructions for the actual parts.
Resolve alignment, access and movement during that trial. Finish using the specified hardware and fastening requirements. Check runner locks and seat controls in the completed installation.
Send the floor comparison with your seat choice
Cameron would keep the labelled hole-centre measurements beside photographs of the current mounting points. Add the physical side and full bracket reference. Include any mismatch with the original drawing so it can be reviewed before parts are ordered.
Give the exact seat version and the adjustment wanted from the change. Ask for the runner, supports and hardware to be itemised with the vehicle bracket. Include the restraint arrangement and the driver’s access requirements.
- C3 year and original market, current steering position and physical side.
- Mounting photographs and labelled measurements compared with Planted’s drawing.
- Details of earlier floor, seat or lower-fitting changes.
- Full SB267 side reference and agreed Standard or Alternate pattern.
- Exact seat version, upper fittings, driver requirements and restraints.
Common questions
Planted lists the Chevrolet Corvette C3, 1968-1982. It expressly warns that the floor bolt pattern varies. Compare the actual mounting holes with its C3 drawing before ordering.
Planted says the bracket may not fit every C3. If the hole pattern differs, changes to the floor or bracket may be required. Have the discrepancy assessed before choosing the fitting parts.
The 1968-1982 label identifies the listed C3 application. It does not replace a comparison of the actual mounting holes. Include earlier floor or mounting changes in the enquiry.
Planted states that all measurements are approximate and taken at the centre of the mounting holes. Use its front, rear and door labels when recording the measurements on the car.
The drawing gives different dimensions for the two sides. For example, the rear span is 15-5/8 inches on physical left and 15-3/8 inches on physical right. Compare each position with its own drawing.
The drawing gives approximate measurements without an acceptable mismatch tolerance. Send the measurements and mounting photographs for review. Do not assume that an apparent difference can be accommodated.
SB267DR is Planted’s Standard physical-left reference. The matching shop variation is labelled RHD Passenger Side. On an LHD car that physical position is the driver’s side.
SB267PA is the Standard physical-right reference. The matching shop variation is labelled RHD Driver Side. Keep the full reference with the actual position and steering arrangement.
The listing’s description says driver side only, while its selectable variations include SB267DR and SB267PA. Have the chosen physical side and exact reference confirmed before ordering.
Confirm the supplied runner pattern separately from the shop’s physical-side selection. The exact runner needs a compatible attachment to the bracket and to the seat or supports.
Standard includes the Recaro slider pattern. Alternate replaces that pattern with Cobra/Scheel-Mann. Agree the supplied version with the upper assembly before ordering.
The Cobra Monaco Pro, Sparco Sprint and OMP TRS-E are options to discuss. Try the exact version with the driver and confirm its permitted mounting method. Trial the complete assembly for cabin clearance.
The Sparco R100, Corbeau Sportline RRS and Cobra Misano Anniversary are base-mounted reclining options to compare. Check the exact seat’s support and movement with its proposed lower fittings.
The linked RRS listing supplies a pair. Each physical position needs its own floor comparison, vehicle bracket and specified lower assembly. Have both positions itemised on the quote.
Use suitable supports when the exact shell permits side mounting. Check their seat attachment positions and their lower connection. Base-mounted seats have a separate seat-side fitting method.
The linked runner offers 291mm and 405mm handle-type choices. Confirm the exact runner reference and attachment dimensions at both interfaces. A handle label alone does not establish the complete pattern.
Planted distinguishes Narrow and Wide Cobra patterns. Narrow is included on both bracket versions; Wide needs Alternate or a separately specified modification. Agree the exact runner and supplied bracket version together.
Have their condition and attachment dimensions checked against the replacement seat and bracket. Record their references and any existing adapters. The old installation does not establish compatibility with a different seat.
Have the direct mounting method and hardware specified for the actual components. Trial the resulting position with each driver. Confirm control reach and cabin clearance before final fitting.
Trial the complete assembly to establish the final position. The seat, bracket and upper fittings all contribute to it. Check the actual driver’s visibility and control reach with the chosen parts fitted.
Check the shell, handles and backrest against the surrounding trim and any cage. Try the movement and runner travel you intend to use. Include getting into and out of the car.
Show the changes and current mounting points in photographs. Include the references of any lower parts proposed for reuse. Have their condition and attachment assessed against the intended assembly.
A harness needs its own routing and anchor assessment with the selected seat and surrounding structure. Follow the component instructions for the complete installation. Competition use also needs checking against the event’s requirements.
Send the C3 details, physical side and floor comparison with your exact seat choice. Include the proposed runners or supports and current restraint attachments. Add the driver’s requirements and details of earlier mounting changes.
Garreth’s top tip
Garreth would try the seat with the driver before settling on the support and adjustment. Include getting in and out of the C3 as well as the seated position. Compare the choices with the proposed lower assembly included.
Cameron’s fitting view
Cameron would put the floor photographs and labelled measurements beside the correct side of Planted’s drawing. Resolve any discrepancy before specifying SB267. Keep the physical-side reference and supplied runner pattern on the same parts list.
Plan your Chevrolet Corvette C3 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Sources: Planted’s physical-left and physical-right SB267 applications and linked original C3 drawing, installation instructions, runner guidance and linked shop listings. Check the actual car and current component instructions with the fitting enquiry.

![Planted Technology Chevrolet Corvette [C3 Chassis] (1968-1982) - Driver / Left *May not fit all C3 Chassis, see online diagram Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/SB267DR-1-300x300.jpg)





