Chevrolet Corvette C6 Bucket Seat and Fitting Guide
Choose the C6 bracket around the belt installation
For a Corvette C6 seat change, identify the belt installation before ordering the floor bracket. Planted lists two non-ZR1 options with different belt tabs and a separate 2009-2013 ZR1 bracket that cannot retain the stock seat-belt receptacle. Each route needs its own parts and restraint assessment.
Garreth would compare the seat’s support with the actual driver and intended use. Cameron would record the current belt attachments and lower fittings beside the chosen bracket reference. Try the full assembly for the driving position and access you need.
At a glance
- C6 generation: 2005-2013; identify the exact model and year.
- Non-ZR1 SB001: belt tab on the inboard side only.
- Non-ZR1 SB250: belt tabs on the inboard and outboard sides.
- ZR1 2009-2013 SB195: stock seat-belt receptacle cannot be retained.
- Physical side, bracket route and runner pattern are separate choices.
- Confirm the complete restraint arrangement and trial the seat in the car.
Keep the C6 identification with the exact year
Chevrolet identifies the C6 generation as 2005-2013. Give the full model and year with the car’s original market and current steering arrangement. State whether it is a ZR1 and include earlier changes to the seats or mounting points.
Planted’s SB001 and SB250 listings span C6/C7, 2005-2019, and exclude ZR1. The separate SB195 application names ZR1, 2009-2013. Keep those restrictions with the actual car when choosing the bracket.
Photograph the attachments on both sides of the seat
Show the installer the current belt and buckle attachments, including the lower assembly around them. Inboard means towards the car’s centre; outboard means towards the door. Include any adapters or changes made during an earlier seat conversion.
The SB001 and SB250 names describe different belt-tab arrangements on the brackets. Have the required arrangement confirmed against the actual restraint installation. The year and a driver-side label alone do not settle that choice. Cameron would keep the photographs with the itemised parts list.
Identify affected seat equipment and connections before removing the existing assembly. Agree how those components and the restraints will work with the replacement seat.
SB001 has an inboard belt tab and excludes ZR1
Planted lists SB001 for C6/C7 chassis excluding ZR1, with a belt tab on the inboard side only. Discuss this route when its tab arrangement suits the confirmed restraint installation. Specify the physical side and supplied runner pattern with the exact seat assembly.
Have the bracket attachment and the belt connection checked separately. A tab on the bracket does not approve every restraint or mounting combination.
SB250 has inboard and outboard belt tabs
SB250 is the other listed C6/C7 non-ZR1 route. Planted describes belt tabs on both the inboard and outboard sides. Have the need for that arrangement confirmed with the existing attachments and the proposed restraint setup.
Keep SB250 distinct from SB001 on the quote. Check the physical side, upper fittings and attachment instructions for the exact components being installed.
-
From £222.60 Incl. VATFrom £185.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
The 2009-2013 ZR1 route loses the stock belt receptacle
Planted lists SB195 separately for the Corvette ZR1, 2009-2013. Its application explicitly says that the stock seat-belt receptacle cannot be retained. That restriction belongs on the parts enquiry before a seat or bracket is ordered.
Have the full restraint arrangement assessed with the exact seat and intended use. The listing does not establish an approved factory-buckle relocation or a complete replacement restraint package. Resolve that installation with the supplier and installer before choosing this route.
Keep the 2009-2013 application with SB195. A ZR1 badge from another Corvette generation needs a separate fitting check.
Order by physical side and agree the runner pattern separately
For each of these three bracket families, Planted’s DR reference is physical left and PA is physical right. The matching shop choices use RHD Passenger Side for DR and RHD Driver Side for PA. Confirm the exact position with the actual steering arrangement.
Physical left is the driver’s position on an LHD car, despite the shop’s RHD Passenger label. The product descriptions also say driver side only while the selectable variations include both sides. Ask for the full SKU and physical position to be confirmed on the quote.
Choose Standard or Alternate independently of the side. Standard includes the Recaro slider pattern; Alternate replaces that pattern with Cobra/Scheel-Mann. Check the exact runner at the bracket and at the seat or supports.
| Bracket | Listed route | Physical left | Physical right | Restraint detail to resolve |
|---|---|---|---|---|
| SB001 | C6/C7 excluding ZR1 | SB001DR, shop RHD Passenger | SB001PA, shop RHD Driver | Inboard belt tab only |
| SB250 | C6/C7 excluding ZR1 | SB250DR, shop RHD Passenger | SB250PA, shop RHD Driver | Inboard and outboard belt tabs |
| SB195 | ZR1 2009-2013 | SB195DR, shop RHD Passenger | SB195PA, shop RHD Driver | Stock seat-belt receptacle cannot be retained |
Planted’s Alternate references add COBRA- before the Standard reference, for example COBRA-SB250DR. Have the supplied pattern agreed separately from the shop’s side selection.
Try the fixed buckets with the driver and lower assembly
The Cobra Monaco Pro, Sparco Sprint and OMP TRS-E are fixed-back options to discuss. Their listings describe base and side mounting options. Confirm the permitted method for the exact seat version and itemise the fittings below it.
Garreth would try the cushion and backrest support with the driver. Check getting over the bolsters as well as sitting in the driving position. Trial the shell’s widest points against the actual cabin with the chosen bracket and upper assembly.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Check backrest movement and adjustment controls
The Sparco R100, Corbeau Sportline RRS and Cobra Misano Anniversary are base-mounted reclining options to compare. Garreth would assess the support and adjustment with the actual driver. Try the controls from the seated position.
Check backrest movement and runner travel against the cabin. The linked RRS listing supplies a pair; each position needs its own confirmed bracket and lower fittings. Include the restraint arrangement for each seat on the quote.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Match the Cobra runner to the supplied bracket pattern
The Cobra Premium runner listing has 291mm and 405mm handle-type choices. Confirm the exact runner reference and attachment dimensions at both interfaces. Its handle label alone does not establish the complete bolt pattern.
Planted distinguishes Narrow and Wide Cobra slider patterns. Narrow is included on both bracket versions; Wide needs Alternate or a separately specified modification. Agree the bracket version with the runner before ordering.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Trial the Sparco runner with the seat above it
The linked Sparco runner is an adjustment option to assess with the proposed seat. Check its upper attachment to the seat or supports and its lower attachment to the supplied bracket. Specify the required hardware with those connections.
Trial the handle and locking operation in the car. Check each regular driver’s required travel and the resulting seating position. The selected seat and all lower components contribute to the final height.
Specify supports for the exact mounting method
The linked Sparco steel supports are an option for a shell that permits side mounting. Match their attachment positions to the seat and confirm their lower connection to the runner or vehicle bracket. Use the instructions for the actual components.
A base-mounted seat needs its own compatible seat-side fittings.
Check the driving position with the complete assembly
Trial the assembly with the actual driver and compare visibility and pedal reach with the current installation. Check access to the controls. Include a helmet and other equipment when they form part of the intended use.
Move the seat through the adjustment range you intend to use. Check the shell, backrest and handles against the door trim, centre area and any cage. Try getting into and out of the car with the proposed seat in position.
Assess harness routing and anchors as a complete installation
If a harness is proposed, identify the exact model and intended use. Have its routing and anchors assessed with the chosen seat and surrounding structure. Include any cage or other parts involved in the installation.
The bracket’s belt tabs do not establish approval for every harness attachment. Follow the seat and harness instructions for the complete combination. On the SB195 ZR1 route, the stock-receptacle restriction still needs resolving with the full restraint arrangement. For competition use, have the completed installation checked against the event’s requirements.
Trial the bracket and upper fittings before final assembly
Agree the bracket application and restraint arrangement before removing the old seat. Planted’s fitting sequence checks the bracket in the vehicle, assembles the upper components outside it and trials the complete seat assembly. Use the current instructions for the exact parts.
Resolve alignment, movement and access during that trial. Finish using the specified hardware and fastener requirements. Check runner locks, seat controls and restraint operation in the completed installation.
Send the belt photographs with the chosen seat version
Cameron would keep the full model details and photographs beside the proposed bracket reference. Record the physical side and supplied pattern. Include any current adapters or fittings proposed for reuse.
Give the driver’s requirements and exact seat version with the restraint plan. Ask for the bracket, runner and seat-side fittings to be itemised together. On a 2009-2013 ZR1, have the SB195 stock-receptacle restriction addressed before ordering.
- Exact C6 model and year, ZR1 identification where applicable, original market and steering position.
- Photographs of the current floor attachments, belt and buckle fittings, including earlier changes.
- SB001, SB250 or SB195 route, full physical-side reference and agreed runner pattern.
- Exact seat version, runner and any side supports or other fittings needed.
- Driver and access requirements, intended use and the complete restraint arrangement.
Common questions
Chevrolet identifies C6 as 2005-2013. Include the exact year and model in the enquiry, along with ZR1 identification where applicable. The fitting route still needs checking against the actual car.
Planted lists SB001 and SB250 for C6/C7 chassis, 2005-2019, excluding ZR1. The brackets have different belt-tab arrangements. Confirm the exact car and restraint installation before choosing one.
SB001 is the non-ZR1 option with a belt tab on the inboard side only. Have that arrangement checked against the actual installation. Specify the physical side and supplied runner pattern separately.
SB250 is the non-ZR1 option with belt tabs on both inboard and outboard sides. Confirm the required arrangement with the installer using the current belt attachments and proposed restraints.
Inboard is towards the centre of the car; outboard is towards the door. Photograph the current attachments on both sides of the seat. Keep those positions clear when discussing the bracket.
Have the tab arrangement checked against the actual restraint installation. Include the model and year with photographs of the current attachments. Earlier seat or belt changes need assessing too.
Both manufacturer applications exclude ZR1. Planted lists SB195 separately for the 2009-2013 ZR1, with a stock seat-belt receptacle restriction. Keep the complete application with each reference.
Planted says the stock seat-belt receptacle cannot be retained with SB195. Have the complete restraint arrangement assessed before ordering. The bracket listing alone does not establish a replacement package.
The listing does not establish an approved relocation method. Have the intended restraint installation resolved with the supplier and installer for the actual car, seat and use before choosing the bracket.
Its listed application is ZR1, 2009-2013. A ZR1 from another generation needs a separate fitting check. Keep the generation and year with the full bracket reference.
The Standard physical-left references are SB001DR, SB250DR and SB195DR. Their matching shop variations are labelled RHD Passenger Side. On an LHD car physical left is the driver’s position.
SB001PA, SB250PA and SB195PA are the Standard physical-right references. Their matching shop variations use RHD Driver Side. Confirm the full reference with the actual position being changed.
The descriptions use driver-only wording while the selectable variations include both DR and PA references. Have the physical side and exact SKU confirmed on the quote before ordering.
Agree Standard or Alternate separately from the shop’s side selection. Check the runner’s attachment to the bracket and to the seat or supports. Keep all of those references together.
Standard includes the Recaro slider pattern. Alternate replaces that pattern with Cobra/Scheel-Mann. Planted’s Alternate SKU adds COBRA- to the corresponding Standard reference.
The Cobra Monaco Pro, Sparco Sprint and OMP TRS-E are options to compare with the driver. Confirm the exact version’s permitted mounting method and trial the completed assembly for cabin clearance.
The Sparco R100, Corbeau Sportline RRS and Cobra Misano Anniversary are base-mounted reclining options. Try the support and controls with the driver. Check the proposed movement against the cabin.
The linked RRS listing supplies two seats. Each physical position needs a confirmed bracket and complete lower assembly. Include the restraint arrangement for each side on the quote.
Use suitable supports when the exact shell permits side mounting. Confirm their attachment positions and lower connection. Base-mounted seats use their own seat-side fitting method.
The linked runner offers 291mm and 405mm handle-type choices. Have the exact runner reference and attachment dimensions checked at both interfaces. Its handle label alone does not establish the complete pattern.
Planted distinguishes Narrow and Wide Cobra patterns. Narrow is included on both bracket versions; Wide needs Alternate or a separately specified modification. Agree the exact runner with the supplied bracket version.
Discuss the linked Cobra or Sparco runner with the chosen seat and bracket. Both attachment interfaces need checking. Trial the handle, locks and required travel with the complete assembly in the car.
Trial the complete assembly to establish the final position. The seat and all lower fittings contribute to the height. Check the actual driver’s visibility, pedal reach and access to controls.
Have their condition and both attachment interfaces assessed with the replacement components. Include references and photographs of the parts you would like to retain. Their previous use does not confirm the new combination.
The harness needs its own routing and anchor assessment with the seat and surrounding structure. Follow the component instructions for the complete installation. Competition use also needs checking against the event’s requirements.
Send the exact C6 model and year with mounting and belt photographs. Include the physical side, preferred seat version and proposed upper fittings. Add the driver, access and restraint requirements, including the SB195 receptacle restriction where applicable.
Garreth’s top tip
Garreth would compare the support with the driver and try getting in and out of the car. Include the lower assembly when judging the driving position. Try a fixed bucket and a recliner against the adjustment and access you need.
Cameron’s fitting view
Cameron would keep the belt photographs beside the full bracket reference. Confirm the required tab arrangement and physical side before choosing the upper fittings. For SB195, resolve the stock-receptacle restriction with the complete restraint installation first.
Plan your Chevrolet Corvette C6 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Sources: Chevrolet’s generation history, Planted’s SB250 left, SB250 right, SB001 left, SB001 right, SB195 left, SB195 right applications, installation instructions, runner guidance and linked shop listings. Confirm the actual car and current component instructions with the fitting enquiry.

![Planted Technology Chevrolet Corvette [C6/C7 Chassis Excluding ZR1] (2005-2019) - Driver / Left *Seat belt tab on inboard side only Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/SB001DR-2-300x300.png)
![Planted Technology Chevrolet Corvette [C6/C7 Chassis Excluding ZR1] (2005-2019) - Driver / Left *Seat belt tab on inboard and outboard sides Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/SB250DR-1-300x300.jpg)






