Acura Integra 1990 to 1993 Bucket Seat and Fitting Guide
Match the original application before choosing the lower fittings
Which fitting kit do you need for a 1990 to 1993 Acura Integra? Planted names two applications in this range: US models with the automatic seat belt retractor, and models without it. Match the exact application and physical side before choosing the seat and upper fittings. PCI also lists DA side-mount assemblies for 1989 to 1991. Keep that separate application label with the enquiry so we can check the actual car before choosing a route.
Garreth would try the seat support and bolster access with the driver. Cameron would keep the original vehicle details beside photographs of the present mounts. Include any previous seat or belt changes in the enquiry.
At a glance
- SB030 names Acura Integra US models with the automatic seat belt retractor, 1990 to 1993.
- SB238 names Acura Integra models without the automatic seat belt retractor, 1990 to 1993.
- Planted uses physical-left DR and physical-right PA references. PCI uses L and R within its full DA codes.
- PCI names the DA application as 1989 to 1991; confirm its exact body, market and original mounting arrangement.
- The PCI S1 standard assembly has sliders and S1 supports. The adjustable A1 uses its own A1 supports and a position set during fitting.
- Confirm the original configuration, build, actual body, market and steering side with the fitting enquiry.
- Specify a complete lower arrangement for each physical seat position and confirm the supplied quantities.
- The scaled 345mm by 271mm Sparco drawing shows named seat-side centres; the Integra floor needs its own reference.
Identify the original application and present mounting arrangement
Planted separates these two 1990 to 1993 Integra applications by their named seat belt retractor configuration. Give the original vehicle identification and build with the enquiry. Include the actual body, market and steering side.
Tell us about previous changes to the seats, belt arrangement or mounting points.
Send photographs of the present floor connections and buckle hardware. Include existing adapter references where known. Cameron would compare the exact supplied bracket application with those details before selecting the upper fittings.
Keep the application qualifier with each physical-side reference
SB030 is named for US models with the automatic seat belt retractor. SB238 is named for models without that retractor. Both manufacturer applications cover 1990 to 1993.
Keep the original configuration details with the photographs of the car as it is now.
The shop uses RHD seating-side variation labels. Match the full supplied code to the actual steering side and physical position. Send the vehicle details for a manufacturer application check if its configuration is uncertain.
| Manufacturer application | Physical position | Manufacturer reference | Cobra alternate reference |
|---|---|---|---|
| SB030: US models with auto retractor | Left | SB030DR | COBRA-SB030DR |
| SB030: US models with auto retractor | Right | SB030PA | COBRA-SB030PA |
| SB238: models without auto retractor | Left | SB238DR | COBRA-SB238DR |
| SB238: models without auto retractor | Right | SB238PA | COBRA-SB238PA |
Choose the SB030 route for its named US application
The SB030 card links to the Planted bracket named for US Integra models with the automatic seat belt retractor, 1990 to 1993. SB030DR identifies physical left and SB030PA physical right. Confirm the complete supplied reference for the position being changed.
Keep the manufacturer’s US-model and equipment qualifiers on the parts list.
List the selected seat and any runner or fixed connection alongside that bracket. Include supports where required by the shell and the retained buckle hardware. Confirm the complete supplied arrangement before ordering.
Choose the SB238 route for its named equipment configuration
The SB238 card links to the Planted application for Integra models without the automatic seat belt retractor, 1990 to 1993. SB238DR identifies physical left and SB238PA physical right. Match the full supplied code with the actual steering side.
Include the original equipment details and present mounting photographs in this enquiry as well.
For two front seats, specify each physical side separately. Confirm the bracket family, upper fittings and quantities for the complete order. A pair of seats still needs the lower arrangement selected for each position.
Check PCI's separate 1989 to 1991 DA application
PCI names both its sliding and adjustable DA mounts for the Integra 1989 to 1991. Send the original vehicle identification, actual body and market so we can check that application against the car. The Planted 1990 to 1993 range and its equipment branches need their own checks.
For a 1992 or 1993 car, ask for an exact manufacturer application before selecting a PCI mount. A shared Integra name or DA code cannot extend the stated year range.
Cameron would match the complete L or R code to the physical seat position. On the current shop variations, L is physical left and RHD passenger; R is physical right and RHD driver. Include the actual steering side with the enquiry.
Choose PCI S1 for its sliding side-mount arrangement
The sliding DA family is SM-DA-S1. PCI lists SM-DA-L-S1 for physical left and SM-DA-R-S1 for physical right within its 1989 to 1991 application. Confirm the exact supplied side and vehicle before ordering.
PCI specifies SM-SIDE-S1 supports as standard with its slider assemblies. Its S1 sliders provide fore-and-aft movement. Check the supplied package before adding parts; the separate Cobra and Sparco runners below are options for a confirmed Planted assembly.
Match the actual side-mounted shell to the S1 supports, including its fixing positions and fasteners. Trial the complete assembly for reach, release-handle access and cabin clearance. Garreth would choose the sliding route when that movement is needed by the driver.
-
From £330.00 Incl. VATFrom £275.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Set the PCI A1 position during fitting
The adjustable DA family is SM-DA-A1, with SM-DA-L-A1 for physical left and SM-DA-R-A1 for physical right. Keep the maker’s 1989 to 1991 application on the order enquiry and confirm the original vehicle details.
The A1 position is set during fitting. PCI specifies SM-SIDE-A1 supports as standard for this assembly; check the actual supplied package and instructions for any support option. A separate runner would change the assembly and needs its own confirmation.
Cameron would compare the exact shell fixings with the A1 supports before trialling the driving position. The manufacturer’s general adjustment range cannot predict the finished height or clearance in a particular Integra. Check access to the adjustment hardware as well as pedal and steering reach.
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Select the Planted runner pattern with the exact seat references
Planted’s general FAQ distinguishes Standard and Alternate slider patterns. Wide Cobra and Scheel-Mann runners require its Alternate pattern. The narrow Cobra runner fixings are included on both versions.
Both Integra application families have Cobra-prefixed alternate references for each physical side.
Send the full seat and runner references before choosing the supplied bracket version. Compare the upper seat connection and lower bracket connection independently. Cameron would confirm the complete arrangement with the selected SB030 or SB238 application.
Compare fixed-back seats by support and mounting route
The Cobra Monaco Pro is a fixed-back steel-frame candidate with listed base and side mounting choices. Try the cushion and support with the driver. Confirm the actual version and selected lower arrangement together.
The standard Sparco Sprint card uses the BRR0003 family reference; its maker catalogue shows base and side fixing routes.
The OMP TRS-E Velour is another steel-frame choice with both routes listed. Compare bolster access and the position you want in the Integra before choosing the finish. Garreth would put the driver’s support and entry first in that comparison.
For either PCI DA route, confirm the side-mounted version of the chosen shell and its interface with the specified PCI supports. The base-mount drawing later in this guide is a separate connection.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Try reclining choices with their controls and lower fittings
These reclining choices need a complete base-mounted arrangement on the applicable Planted bracket. The PCI DA S1 and A1 listings specify side-mounted bucket-seat assemblies; they do not establish a mounting route for these recliners.
The Sparco R100 is a base-mounted reclining option to try. The shop record linked here uses legacy 00961NR, while the newer catalogue names the 009014 family. Confirm the actual supplied version before choosing fittings from its drawing.
The Corbeau Sportline RRS card is a pair of seats on the listed standard base. Each physical position needs its own Integra bracket and upper assembly. Confirm the package contents and quantities for the complete order.
The Cobra Misano Anniversary has its own reclining mechanism, shell and trim choices. Trial the controls and backrest movement beside the actual door and tunnel. Include any access needed behind the front seats in that trial.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Match the Cobra runner within the Planted assembly
For a confirmed Planted route, the Cobra Premium runner listing offers 291mm and 405mm handle-width options. Match the actual runner to the seat and supplied bracket’s slider pattern. The handle label alone cannot identify the complete fixing layout.
Send the full Monaco or Misano reference with the runner enquiry.
Check the upper seat connection and lower bracket connection as separate interfaces. Trial the required movement and release-handle access in the Integra. Include the runner’s thickness when comparing the complete driving position.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Specify the Sparco slider within the Planted assembly
The Sparco 0049306 runner is a sliding option to discuss for a confirmed Planted assembly with the named Sparco seat. Its catalogue shows a 271mm longitudinal fixing distance. Confirm the entire upper and lower layout with the supplied seat, supports where used and selected bracket version.
The named Sprint and R100-family seat-side base fastenings below are 345mm by 271mm.
Trial both rails through the travel required by the driver and check that they release and lock together. Include the handle and surrounding trim throughout that movement. A shared dimension at one connection leaves the other interfaces to verify.
Specify the supports for the chosen mounting route
For a side-mounted shell, supports join the seat’s side fixings to the lower assembly. The Sparco steel supports shown here are a candidate for the exact Sparco shell and its instructions. Use another seat family’s own confirmed support combination.
The shell’s side fixings and the support’s lower pattern each need their own reference.
Cameron would check the exact shell, support orientation and specified fasteners before comparing the lower connection. Include any runner and the supplied SB030 or SB238 version in that drawing comparison. The vehicle application alone cannot specify those upper components.
PCI specifies its own S1 or A1 supports with the corresponding DA assembly. Confirm those supplied parts before buying another support pair. Left and right support pieces sit beside one shell; each front seat position still needs its own complete vehicle-mount arrangement.
Plan fixed positioning as its own complete arrangement
Planted publishes separate installation arrangements for base-mounted and side-mounted seats, with and without sliders. Its FAQ describes its own side mounts with sliders beneath them. Ask us to specify the complete fixed arrangement if adjustment is not required.
Removing a runner changes the connection and finished position.
Trial the selected components in the actual car using the relevant instructions. Check pedal and steering reach with the driver. Garreth would also try getting over the bolster and the access needed behind the seat.
The PCI A1 is a separate adjustable assembly for its named DA application. Choose it with its own supports and instructions, then trial the position with the driver.
See the named Sparco seat-side centres at one scale
The named Sprint and R100-family lower fastenings in the Sparco catalogue measure 345mm across and 271mm front to rear. Both dimensions use the same scale in the drawing. Confirm the exact supplied seat version before choosing components around those centres.
The Integra floor, full selected bracket slot layout and outside shell dimensions need separate measurements.
Trial the preferred seat and complete lower assembly in the cabin. Include shoulder room and access to the controls beside the actual trim. A Cobra, Corbeau or OMP choice needs that exact version’s drawing for its own seat connection.
Source: Sparco 2025 manufacturer catalogue, printed pages 178 and 326 to 327. The shop’s R100 reference needs supplied-version matching.
These base-fixing centres do not specify the side-fixing interface of a PCI S1 or A1 assembly. Use the selected shell and PCI support drawings for that connection.
Choose the restraint with the shell and actual anchors
Include the intended belt arrangement before the lower fittings are finalised. Match the exact shell and restraint instructions to the actual anchors and driver. Photograph the existing buckle connection and retained hardware.
For a harness enquiry, show any proposed bar or cage and its specified attachments.
Check the shell openings, strap configuration and anchors as one arrangement. Trial routing and buckle access with the seat in its intended position. Choose a harness product once that configuration has been established.
- Original belt: check the exact shell, buckle position and retained mounting hardware.
- Harness: confirm the required straps, shell openings and available anchor arrangement together.
- Two seats: specify each physical side, quantities and the adjustment needed by each occupant.
Send the original configuration and full parts references together
Send the original vehicle identification, build, body, market and steering side. Include the original equipment details and photographs of the present mounts. Show previous adapters and the current buckle connection.
Describe the adjustment, access, retained functions and belt arrangement wanted from the seat change.
Include the exact seat and every proposed lower component. Trial the complete position with the actual driver before confirming reach and clearance. Cameron would compare that arrangement with the application and physical-side references on the enquiry.
Common questions
Which Integra application does SB030 cover?
Planted names Acura Integra US models with the automatic seat belt retractor, 1990 to 1993. Keep both the market and equipment qualifiers with the enquiry. Confirm the actual build, body, floor and supplied physical-side reference.
Which Integra application does SB238 cover?
Planted names Acura Integra models without the automatic seat belt retractor, 1990 to 1993. Send the original configuration details and present mounting photographs. Confirm the exact supplied bracket and upper arrangement for the car.
What should I send if the seats or belt arrangement have changed?
Include the original vehicle and equipment details with photographs of the present fittings. Show adapters or floor changes and any known component references. Ask for the manufacturer application for that actual car and proposed assembly.
How do I choose between the shop’s seating-side variations?
Give the actual steering side and physical seat position. Planted uses physical-left DR and physical-right PA within each selected family. PCI uses L for physical left and R for physical right within the full DA S1 or A1 code. Keep the complete supplied reference with the parts list.
Which physical-side and alternate codes are listed?
SB030DR and SB238DR identify physical left within their respective families; SB030PA and SB238PA identify physical right. Each has a Cobra-prefixed alternate reference. The table keeps the application qualifier with each code.
How do Standard and Alternate runner patterns differ?
Planted’s general FAQ directs wide Cobra and Scheel-Mann runners to the Alternate pattern and includes narrow Cobra runner fixings on both. Send the full seat and runner references. Confirm the supplied version within the selected Integra bracket family and both fixing interfaces.
Does the RRS pair include two Integra brackets?
The linked card describes a pair of seats on the named standard base. Specify a vehicle bracket and selected upper assembly for each physical side separately. Confirm current contents and quantities before ordering.
Can I specify a fixed seat position?
Ask us to specify the full fixed arrangement for the exact seat and car. Planted publishes separate installation arrangements with and without sliders. Check the connections and final position for the chosen assembly. PCI also lists its A1 adjustable assembly for the separate 1989 to 1991 DA application; confirm the car and full supplied configuration before selecting it.
What does the scaled 345mm by 271mm drawing show?
It shows named Sparco seat-side lower fastening centres in the maker catalogue. The actual Integra floor and full selected bracket layout need separate references. Match the supplied seat version and every remaining interface.
What if the original mounts have been changed?
Photograph the original locations and current adapters or floor alterations. Include the previous component references where known. Check the named application against the floor and assembly the car actually has.
How much lower will the replacement seat sit?
Compare the current position with a trial of the complete proposed assembly and actual driver. The cushion, shell angle and lower components all contribute. The bracket code alone cannot predict a reduction.
What completes the seat and fitting enquiry?
Send the chassis identification, body, build, steering side and mounting photographs. Include the exact seat and fitting references, access and adjustment wanted, retained functions and belt arrangement. Show any previous adaptations.
Does PCI cover every year in this guide?
PCI names its DA S1 and A1 mounts for 1989 to 1991. Confirm the actual body, market and original mounts for a 1990 or 1991 enquiry. A 1992 or 1993 car needs an exact manufacturer application before either PCI kit is selected.
What is the difference between the PCI S1 and A1 routes?
The S1 is a sliding assembly supplied as standard with SM-SIDE-S1 supports. The A1 position is set during fitting and uses SM-SIDE-A1 supports as standard. Confirm the exact DA physical-side code, supplied components and shell interface for either route.
Should I add separate runners or supports to a PCI kit?
Check its actual supplied contents first. PCI specifies its S1 sliders and standard S1 supports for the sliding assembly, and standard A1 supports for the adjustable assembly. Any changed support or added runner needs confirmation for that complete configuration.
Can the reclining seats use the listed PCI DA assemblies?
The listed PCI DA assemblies specify side-mounted bucket seats. Choose a separately confirmed base-mounted route for the exact recliner, relevant Planted application and supplied upper fittings. Include the controls and backrest movement in the cabin trial.
Garreth’s top tip
Garreth would try the cushion, support and bolster access with the driver before choosing the finish. Include how the Integra is used and any access needed behind the front seats. Keep the complete lower arrangement with the chosen seat reference.
Cameron’s fitting view
Cameron would keep the original market and equipment details beside the present mounting photographs. Match the selected Planted application or the separate PCI DA year range and full physical-side code. Confirm the supplied upper fittings, then trial the complete assembly with the actual driver.
Plan your Acura Integra 1990 to 1993 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Sources: PCI S1 applications and standard assembly, A1 applications and standard assembly, S1 supports and A1 supports; Planted application records, slider-pattern and market guidance and assembly-specific instructions; Sparco 2025 catalogue, printed pages 178 and 326 to 327; linked shop listings. Confirm the current supplied versions and actual car before completing the package.

![Planted Technology Acura Integra [US models w/auto seat belt retractor] (1990-1993) Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/SB030PA-2-300x300.jpg)
![Planted Technology Acura Integra [models WITHOUT auto seat belt retractor] (1990-1993) Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/SB238PA-2-300x300.jpg)







