Volvo V70R Second Generation Bucket Seat and Fitting Guide
Match the SB410 bracket to the car and chosen seat
For a second-generation V70R seat change, start with the actual car and the adjustment you want to keep. Our listed Planted route is the SB410 floor bracket. Choose the seat and the fittings above that bracket as a complete assembly.
Garreth would try the support and access of the intended seat before choosing its trim. Cameron would identify the physical seating side and compare the lower connections. Send the car’s build details and photographs of the existing mounts with the enquiry.
At a glance
- Planted’s application table names SB410 for the second-generation Volvo V70R under its 2000 to 2007 bracket application.
- The maker references are SB410DR for physical left and SB410PA for physical right; confirm the actual shop variation and driving side before ordering.
- Standard and Alternate slider patterns are a separate choice from the seating side.
- Specify a base-mounted seat or a side-mounted shell, then the corresponding supports and any sliding adjustment.
- The scaled 345mm by 271mm drawing describes the named Sparco seat-side fastening, separate from the Volvo floor.
- Confirm the complete restraint and buckle arrangement with the chosen shell and actual car.
Identify the actual V70R and existing seat mounts
Planted’s application table labels this application as the second-generation V70R, with a 2000 to 2007 range. Use that as the bracket application to check against the car’s build details. The label alone does not establish when a particular R version was produced.
Include the steering side, physical seating position and any previous changes to the floor or factory seat assembly.
The manufacturer’s general FAQ asks owners of other markets and conversions to confirm the actual floor. Cameron would compare the current mounts before specifying the package. Standard V70 or S60 enquiries need their own exact application check.
Use SB410 as the named vehicle connection
The listed SB410 provides a route from the named V70R application to an aftermarket seat assembly. The manufacturer’s application records identify SB410DR on physical left and SB410PA on physical right. Match the complete manufacturer code to the position wanted.
Our listing has RHD Driver Side and RHD Passenger Side options; the actual supplied variation code still needs confirming.
Specify the floor bracket separately from the seat, upper fittings and retained hardware. Check the buckle connection and any previous mounting changes at the same time. A bracket family reference does not establish everything supplied in the order.
-
From £224.95 Incl. VATFrom £187.46 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Choose the bracket pattern around the runner
Planted’s general fitting FAQ distinguishes Standard and Alternate slider patterns. Standard includes its Recaro slider interface; Alternate substitutes the wide Cobra and Scheel-Mann interface. The FAQ says the narrow Cobra slider pattern is included on both.
The SB410 application records also carry Cobra-prefixed alternate codes.
Give us the actual runner reference so we can confirm the supplied bracket version and both fixing interfaces. A handle-width label is only part of that information. Cameron would settle the complete combination before the parts are ordered.
Compare fixed-back seats by support and mounting route
The Cobra Monaco Pro is a fixed-back steel-frame seat to try for support and bolster access. Its listed base and side mounting choices need the matching lower arrangement. Confirm the full supplied version and label before selecting the fittings.
The standard Sparco Sprint card carries the BRR0003 family reference, with base and side fixing routes shown in the maker catalogue.
The OMP TRS-E Velour is another steel-frame option, with base or side mounting listed. Try the cushion and entry as well as the seated position. Garreth would choose the seat that suits the driver before settling the trim and complete V70R fitting enquiry.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Try reclining choices with their controls and lower fittings
The Sparco R100 is a base-mounted reclining option. Our listing uses the legacy 00961NR reference, while the newer catalogue uses the 009014 family. Confirm the actual supplied version before using the catalogue drawing to choose fittings.
The Corbeau Sportline RRS card shown here is a pair of seats on the listed standard base; each physical position still needs its own vehicle bracket and selected upper assembly.
The Cobra Misano Anniversary has its own shell, reclining mechanism and trim choices. Compare the cushion and bolster access with the other seats. Trial the controls and backrest movement beside the actual door and tunnel before confirming the installation.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Match the Cobra runner to both connections
The Cobra Premium runner listing offers 291mm and 405mm handle-width options. Select the runner for the exact seat and the supplied SB410 slider-pattern version. The handle label does not establish the lower hole layout on its own.
For a Monaco or Misano enquiry, send the complete seat and runner references together.
We would check the upper seat connection and the lower floor-bracket connection independently. Confirm the useful travel and room for the release handle in the V70R. The runner’s thickness is also part of the final seating position.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Specify the Sparco slider with the actual seat version
The Sparco 0049306 runner is a sliding option to discuss with the named Sparco seats. The catalogue shows a 271mm longitudinal fixing distance. Confirm its complete upper and lower layout against the seat, supports where used and supplied SB410 version.
The named Sprint and R100-family seat-side base fastening discussed below is 345mm by 271mm.
Check that both rails release and lock throughout the travel required by the driver. Include handle access and the surrounding trim in that trial. A shared dimension at one connection does not verify the remaining assembly.
Use supports specified for the chosen side-mounted shell
A side-mounted bucket needs supports connecting its side fixings to the lower assembly. The Sparco steel supports shown here are a candidate to specify with the selected Sparco shell and its instructions. Other seat families need their own confirmed support combination.
Seat-side fixings and the support’s lower fixing pattern are separate interfaces.
Cameron would match the support orientation and fastener specification to the exact shell, then check the connection below it. Include any runner in that drawing comparison. The shell label and the vehicle-bracket application answer different parts of the enquiry.
Plan fixed positioning as its own complete arrangement
Planted publishes separate installation arrangements for base-mounted and side-mounted seats, with and without sliders. Its FAQ describes its own side mounts around an arrangement using sliders beneath them. Removing a runner changes that connection and the finished position.
If you want a fixed seat, ask us to specify that arrangement before ordering the lower fittings.
Trial the vehicle bracket and the proposed assembly using the relevant component instructions. Check reach and clearance with the actual driver. Garreth would keep getting in and out of the seat in that decision, alongside the final driving position.
See the named Sparco seat-side centres at one scale
The Sparco catalogue gives 345mm across and 271mm front to rear for the named Sprint and R100-family lower fastenings. The drawing shows those two dimensions at one scale. Confirm the exact supplied seat version before using them to select components.
These are seat-side fastening centres; the Volvo floor pattern, full SB410 slot layout and outside seat dimensions are separate measurements.
Measure the preferred seat and complete lower assembly in the actual cabin. Include shoulder room and access to the controls. For a Cobra, Corbeau or OMP choice, use that exact version’s drawing instead of inheriting the Sparco pattern.
Source: Sparco 2025 manufacturer catalogue, printed pages 178 and 326 to 327. The shop’s R100 reference needs supplied-version matching.
Choose the restraint with the shell and actual anchors
Include the intended belt arrangement before the fittings are finalised. Match the selected seat and restraint instructions to the actual anchors and driver. A bracket tab or a set of harness openings is one part of that complete plan.
Send photographs of the existing buckle connection and any proposed harness bar or cage. We would check routing and buckle access with the seat in its intended position. Choose a harness product after its configuration and attachments are established.
- Original belt: check the exact shell, buckle position and retained mounting hardware.
- Harness: confirm the required straps, shell openings and available anchor arrangement together.
- Two seats: specify each physical side, quantities and the adjustment needed by each occupant.
Bring the car and complete seat assembly into one enquiry
Send the actual build details and steering side with photographs of the current floor mounts. Include the complete seat, trim and runner references. Tell us which original functions and restraint arrangement you want to retain.
We can then check the physical side, supplied SB410 pattern and the separate upper fittings together.
Measure the existing position if a lower seat is the aim. The cushion, shell angle and every fitting below the seat affect the result. Cameron would check the complete trial position before confirming reach and clearance.
Common questions
Which bracket is listed for the second-generation V70R?
Our listing and the manufacturer’s application records name Planted SB410. The table labels the application 2000 to 2007; match the actual car and original floor with the current supplied bracket before ordering.
How should I check the bracket application against my car?
Send the actual build details and specification with photographs of the original seat mounts. Planted’s stated bracket application is the starting point for that check. An earlier conversion or different market can change the package that needs specifying.
Which code is physical left or right?
The manufacturer’s records identify SB410DR for physical left and SB410PA for physical right. Match those physical positions to the actual steering side. Confirm the shop variation’s full supplied code with us.
Can I use this application for a standard V70 or S60?
Those enquiries need their own exact manufacturer application check. Send the car’s build details and existing mount photographs. A related model name does not confirm the same fitting package.
What changes between Standard and Alternate patterns?
Planted’s general FAQ says Standard includes its Recaro slider interface and Alternate substitutes the wide Cobra and Scheel-Mann interface. It says the narrow Cobra slider pattern is included on both. Confirm the actual runner and supplied bracket version.
Are sliding runners included with the floor bracket?
Check the current order contents. The floor bracket, seat and upper fitting assembly perform separate jobs. Specify the runner and any shell supports needed for the chosen arrangement.
Can I use a fixed-back bucket without sliding adjustment?
Planted describes separate fixed installation arrangements. Removing a runner changes the lower connection and seating position. Ask us to confirm the complete fixed assembly for the actual shell and car.
Does the Corbeau RRS pair include both V70R brackets?
The linked card is a pair of seats on the named standard base. Specify each vehicle bracket and the selected upper fittings separately. Confirm quantities and both physical positions in the complete order.
What does the 345mm by 271mm drawing describe?
It shows the named Sparco seat-family lower fastening centres from the manufacturer catalogue. It is separate from the Volvo floor and full SB410 layout. Match the exact seat version and each runner interface.
How much lower will the new seat sit?
The cushion, shell angle and lower fittings determine the finished position. Measure the existing position and trial the proposed complete assembly with the driver. A floor-bracket code cannot predict the reduction.
Which harness should I choose?
Choose it with the exact shell and available anchors. Confirm strap configuration, routing and buckle access from the component instructions with the driver seated. Include any existing harness bar or cage in the enquiry.
What information should I send for a complete recommendation?
Send the actual build, steering side, physical seat position and existing mounting photographs. Include the full seat and runner references with the adjustment and restraint arrangement wanted. Tell us about any previous conversion.
Garreth’s top tip
Garreth would choose the seat after trying its support and entry in the intended trim. Keep the adjustment and everyday access you want in that decision. The lower fittings can then be specified around that particular seat.
Cameron’s fitting view
Cameron would match the actual floor and physical side to the supplied SB410 version, then check every connection above it. Record the complete seat, supports and runner references together. Confirm the final position with the driver in the actual car.
Plan your Volvo V70R second generation seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Sources: Planted application records, assembly-specific instructions and slider and market guidance; Sparco 2025 catalogue, printed pages 178 and 326 to 327; linked shop listings. Confirm the current supplied versions and actual car before completing the package.

![Planted Technology Volvo V70R [2nd Generation] (2000-2007) Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/Planted-ImageUnavailable_4fa991da-b9f5-425a-88ae-19f5bafe09ab-300x300.jpg)





