Toyota 4Runner Fifth Generation Bucket Seat and Fitting Guide
Choose the bracket height with the complete seating position
A fifth-generation 4Runner seat change starts with the position you want to achieve. Planted lists Low, Medium and Tall versions of its vehicle bracket. We would choose the height with the seat and every fitting above it in the same plan.
Garreth would compare support, access and the view from the driving position. Cameron would measure the proposed assembly and identify the physical side. Tell us how the 4Runner is used and send photographs of its original seat mounts.
At a glance
- The named bracket choices are Low SB289, Medium SB289.1 and Tall SB289.2 for the fifth-generation application.
- Each height has separate physical-left and physical-right manufacturer references; match the exact side to the actual car.
- The maker labels this fifth-generation application 2009+; confirm the actual generation and build before selecting a bracket.
- Bracket height, physical side and Standard/Alternate slider pattern are separate choices.
- Measure the complete seat, runner and support assembly before choosing on a promised height change.
- The scaled Sparco drawing later in the guide shows seat-side centres, separate from the Toyota floor or bracket height.
Start with the actual fifth-generation car and its mounts
Planted names these brackets for the fifth-generation 4Runner under its 2009+ application. Match the actual build and original mounting arrangement with that specification. A later registration or a shared badge does not establish another generation’s floor.
Send the steering side, physical seating position and photographs of any previous seat conversion.
Include the driving position you want to change and the way the vehicle is used. A road-focused recliner enquiry and a fixed-back build can lead to different upper fittings. Cameron would keep those requirements alongside the vehicle-bracket check.
Compare Low, Medium and Tall as different brackets
Low carries the family reference SB289, Medium is SB289.1 and Tall is SB289.2. Choose one named height for the position being fitted. The decimal suffix identifies a part family, not a measured height difference in inches or millimetres.
The table below separates the manufacturer’s physical-left and physical-right references.
Our listings present RHD seating-side options, so confirm the complete supplied variation code with us. Standard and Alternate slider patterns add another choice within the bracket specification. Garreth would select the height after the complete position has been measured.
| Height option | Physical left | Physical right |
|---|---|---|
| Low | SB289DR | SB289PA |
| Medium | SB289.1DR | SB289.1PA |
| Tall | SB289.2DR | SB289.2PA |
-
From £224.95 Incl. VATFrom £187.46 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £224.95 Incl. VATFrom £187.46 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £224.95 Incl. VATFrom £187.46 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Measure the whole assembly before choosing a height
Record the current cushion position, wheel and pedal reach, headroom and the view wanted from the seat. Include a helmet if that is part of the actual use. The seat shell and cushion can change these measurements before any bracket is chosen.
Add the selected runner and support dimensions to that comparison.
Ask us to confirm the mounting-plane dimensions of the supplied Low, Medium or Tall part against those requirements. A middle label is not a universal default. Cameron would trial the chosen complete assembly before the final position is settled.
Specify the slider pattern separately from height
Planted offers Standard and Alternate slider patterns on these height variants. Standard includes its Recaro slider interface; Alternate substitutes the wide Cobra and Scheel-Mann interface. Its fitting guidance distinguishes the narrow Cobra slider from that wide version.
Give us the actual runner reference, not only the width printed in its product name.
Match the runner’s seat-side and bracket-side fixings independently. Retain the height and physical-side reference in that check. A Low bracket and a Tall bracket need the same care over their chosen upper fittings.
Try fixed-back support with entry and driving reach in mind
The Cobra Monaco Pro is a steel-frame fixed-back choice with listed base and side mounting routes. Try its cushion and bolster access before choosing the lower assembly. The exact supplied seat version determines the fittings to specify.
The standard Sparco Sprint card carries the BRR0003 family reference, with base and side fixing arrangements shown in the maker catalogue.
The OMP TRS-E Velour is another steel-frame option to discuss, with base or side mounting listed. Include getting over the bolster and reaching the controls in the trial. Garreth would compare that access with the support wanted for the vehicle’s actual use.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £244.40 Incl. VATFrom £203.67 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Compare recliners with adjustment and control clearance
The Sparco R100 gives a base-mounted reclining route to discuss. Our listing uses the legacy 00961NR reference, while the newer catalogue uses the 009014 family. Confirm the supplied version before selecting lower fittings from a drawing.
The Corbeau Sportline RRS card is a pair of seats on the named standard base; each side still needs its own vehicle bracket and selected upper assembly.
The Cobra Misano Anniversary has its own shell, mechanism and trim choices. Try the cushion and access to the reclining control, then check the backrest movement required in the 4Runner. Keep the final seating height in the comparison with the other recliners.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £1,649.00 Incl. VATFrom £1,374.17 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Choose the Cobra runner with the exact seat and bracket version
The Cobra Premium listing offers 291mm and 405mm handle-width options. Match the intended seat to the complete runner reference, then confirm the supplied Planted slider-pattern version. A handle label alone does not describe every lower fixing.
One runner assembly serves one seat position.
Check the useful adjustment with the driver seated and the release handle accessible. Add the runner’s thickness to the proposed seating-position measurements. Cameron would confirm the upper and lower connections before completing the order.
-
From £84.00 Incl. VATFrom £70.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Include the Sparco slider in the height and fixing checks
The Sparco 0049306 runner is a separate sliding option for a matching upper assembly. The inspected catalogue shows a 271mm longitudinal fixing distance. Compare its full layout with the actual seat, any supports and the selected Planted bracket.
The named Sprint and R100-family lower seat fastenings discussed below are 345mm by 271mm.
Operate both rails through the travel the driver needs, with room for the release handle. Check locking and surrounding trim as part of that trial. The useful finished position comes from the complete assembly.
Connect a side-mounted shell through its specified supports
The Sparco steel supports shown here are a candidate for the selected Sparco shell and its instructions. Other shell families need their own confirmed support combination. The seat’s side fixing and the support’s lower connection are different interfaces.
Support angle and hole choice also contribute to the driving position.
Confirm the exact shell label, support reference and fasteners, then include the runner or fixed lower arrangement. Trial the complete position with the driver. A vehicle-bracket application does not establish the shell’s clearance beside the door and tunnel.
Specify fixed positioning as a complete alternative arrangement
Planted publishes separate installation arrangements for base-mounted and side-mounted seats, with and without sliders. Removing a runner changes the lower interface and finished height. Ask us to specify the complete fixed arrangement for the chosen shell.
Trial the vehicle bracket against the actual floor and follow the relevant component instructions when assembling the seat. Confirm reach and access before settling the final mounting position. Garreth would make that choice with the driver and the intended use in view.
Use the Sparco seat-side drawing for its named interface
The Sparco catalogue gives 345mm across and 271mm front to rear for the named Sprint and R100-family lower fastenings. Both dimensions below use the same scale. Match the exact supplied seat version before using them to choose components.
The Toyota floor pattern, full Planted slot layout, bracket height and outside shell measurements need their own references. Use the exact maker drawing for a Cobra, Corbeau or OMP selection.
Source: Sparco 2025 catalogue, printed pages 178 and 326 to 327. These centres do not give a Low-to-Tall height difference or an installed-height reduction.
Plan the restraint at the intended seating position
Include the chosen belt arrangement while the seat and height are being specified. Match the shell and restraint instructions to the actual anchors and seated driver. A floor-bracket tab is one connection in that plan.
Send photographs of the existing buckle mount and any proposed harness bar or cage. We would check routing, access and the intended driver position together. Select a harness product after its configuration and attachments are confirmed.
- Original belt: check the selected shell, retained buckle and actual mounting hardware.
- Harness: confirm the shell openings, strap configuration and available anchors.
- Two seats: specify each physical side, height choice, quantity and adjustment requirement.
Send the details needed to choose the height and complete kit
Send the build and generation details, steering side and current mounting photographs. Include the complete seat, runner and support references being considered. Tell us how the existing seating position falls short and what the finished position needs to achieve.
We can then confirm the physical side, named height, supplied slider pattern and upper fittings as one package.
Record the original functions and restraint arrangement you want to retain. Include the available headroom and any equipment around the driver. Cameron would keep those measurements with the exact supplied parts before confirming the final recommendation.
Common questions
Which three bracket heights are listed?
Low is SB289, Medium is SB289.1 and Tall is SB289.2 for Planted’s named fifth-generation 4Runner application. Select the exact physical side and supplied slider pattern as well as the height family.
What do the decimal suffixes mean?
They identify different bracket families in the part references. They should not be read as an installed-height measurement. Confirm the supplied part’s mounting-plane dimensions with the complete seat assembly.
Which code is physical left or right?
The maker records use DR for physical left and PA for physical right within each of these three height families. Match that physical position to the actual steering side and confirm the current shop variation’s full supplied code.
Should I choose Medium if I am unsure?
Choose after measuring the complete seat, runner and support assembly against the position wanted. Include headroom, control reach and the view from the seat. A middle label cannot establish the best position for every driver.
How much lower will Low put the seat?
The finished position depends on the seat cushion, shell angle and every lower fitting. Confirm the supplied bracket dimensions and trial the complete assembly with the driver. The Low label alone does not give a fixed height reduction.
Does 2009+ include every later 4Runner generation?
The maker names a fifth-generation application. Confirm the actual generation and build details before selecting the bracket. A continuing year label does not establish another generation’s floor.
Is the same bracket used on both physical sides?
The manufacturer lists separate left and right references for each named height. Give the seating position as physical left or right as well as the driving side. Confirm each required part when ordering a pair.
Are runners included with the vehicle bracket?
Check the current order contents and specify the selected upper assembly. The vehicle bracket, runner and any shell supports perform separate jobs. Confirm the complete parts and quantities for each seat.
Can I have a fixed seat without sliding runners?
Planted provides separate fixed installation arrangements. Removing a runner changes the connection and final position. Ask us to specify that complete arrangement for the exact shell and selected bracket.
What does the 345mm by 271mm diagram show?
It shows the named Sparco seat-family lower fastening centres from the manufacturer catalogue. It is separate from the Toyota floor, full bracket layout and the three height choices. Match each remaining interface independently.
Which harness should I choose with the new seat?
Choose it with the exact shell, intended position and available anchors. Confirm the strap configuration and routing from the component instructions with the driver seated. Include any existing harness bar or cage in the enquiry.
What should I send for a complete recommendation?
Send the actual generation/build, steering side, physical position and mounting photographs. Include the full seat and fitting references, current position measurements and the result wanted. Tell us the intended use and restraint arrangement.
Garreth’s top tip
Garreth would choose the seat for the support and access wanted in the 4Runner, then settle the bracket height around that complete assembly. Try the intended trim and adjustment before ordering. The driving position matters more than choosing the middle item in a list.
Cameron’s fitting view
Cameron would record the physical side, exact height family and supplied slider pattern, then compare every connection above the floor. Keep the original and proposed position measurements together. Trial the complete assembly with the driver before confirming reach and clearance.
Plan your Toyota 4Runner fifth generation seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Sources: Planted’s Low, Medium and Tall product pages, its application table and assembly-specific fitting instructions; Sparco 2025 catalogue, printed pages 178 and 326 to 327; linked shop listings. Confirm the current supplied components and actual car before completing the package.

![Planted Technology Toyota 4Runner [5th Generation] (2009+) Low Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/SB289PA-1-300x300.jpg)
![Planted Technology Toyota 4Runner [5th Generation] (2009+) Medium Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/merchant-google-ss4u-20261106-f4ba4570-254248-1000-300x300.jpg)
![Planted Technology Toyota 4Runner [5th Generation] (2009+) Tall Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/SB289.2PA-1-300x300.jpg)





