How to Install Sparco Reclining Seats with Slider Rails, DIY Fitting Guide
Seat fitting guide
Fitting a pair of Sparco reclining sport seats such as the R100, R333 or R500 is a job many owners do at home. With the right parts and ordinary tools it is straightforward: a frame made for your car, a Sparco sliding runner kit, and the seat, all on the same bolt pattern.
This guide covers the parts you need, how the bolt patterns line up, the fitting steps in order, and what these seats are and are not for. One thing to know first: Sparco's reclining seats are road and track seats, not FIA approved, so they are not for competition.
- Sparco R100, R333 and R500 recliners are base mount seats on a 345mm by 271mm pattern
- Sparco's sliding runner kit uses the same 345mm by 271mm pattern
- You also need a frame made for your car, or a suitable adaption
- Order runners once per seat; the twin kit covers both seats
- Tighten every fixing to the torque the frame and runner makers specify
- Recliners on runners are for road and track days, not FIA competition

What is on this page
What you need
Gather everything before you start:
- A Sparco reclining seat, such as the R100, R333 or R500
- A Sparco sliding runner kit, one kit per seat, or the twin kit for a pair
- A frame made for your car, from Sparco or another maker on the same pattern
- M8 bolts and washers, if they are not supplied with your parts
- Tools: a socket set, spanners, hex keys and a torque wrench
Lay the parts out and check you have every fixing before the old seats come out. It saves a car sitting without seats while you wait for a bolt.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £449.47 Incl. VATFrom £374.56 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
How the bolt patterns line up
The whole job depends on three parts sharing one pattern:
- The seat: Sparco's recliners bolt down on a 345mm by 271mm base pattern, 345mm side to side and 271mm front to back.
- The runners: Sparco's runner kit uses the same 345mm by 271mm pattern, top and bottom.
- The frame: a Sparco direct fit frame presents the same pattern for the runners to bolt to.
That same 345mm by 271mm pattern is used by OMP and Corbeau base mount seats too. Recaro seats use a wider 405mm pattern and go on Planted brackets, so they are a different job. Our guide to seat bolt patterns explains the differences.

Fitting, step by step
Step 1: fit the runners to the seat. Lay the seat face down on a blanket or soft surface. Place the two runners under the base with the release bar spanning both, so one pull moves both sides together. Line up the holes and fit the M8 bolts and washers loosely.
Step 2: fit the frame to the car. If the frame is not already in, bolt it to the car’s seat mounting points in the floor. Direct fit frames are made to use the factory points, so there should be no drilling.
Step 3: fit the seat and runners to the frame. Lower the seat and runners onto the frame. Slide the seat forward to reach the rear holes and back to reach the front ones, and fit the bolts with large washers.
Step 4: tighten and check. Tighten every bolt evenly, to the torque the frame and runner makers specify. Then sit in the seat, run it through its full travel, and make sure it locks firmly in each position on both sides.
A few things that catch people out:
- Fit the release bar before the seat goes in; it is much harder afterwards.
- Do not force a bolt into a hole that does not line up. Check the frame is the right one for your car and side.
- Keep the factory seat belt buckle in mind. Some frames carry a bracket for it; others expect a harness.
- If the car had side airbags in its factory seats, plan for that before you start.

If you are fitting to a car where the runners need a different route, such as some MX-5s, our answer on whether Sparco runners bolt straight to the car is worth a read, and our guide to fitting Sparco and Corbeau recliners to an M2 frame covers that frame.
Not for FIA competition
Sparco’s reclining seats are not FIA approved, and a recliner on sliding runners is not a setup for competition. The reclining mechanism and runners are not built to the standard motorsport seats are tested to. They suit:
- daily drivers and road cars
- fast road builds and show cars
- non-competitive track days
If you plan to compete, you need an FIA homologated fixed-back bucket seat on side mounts, fixed to the frame, and your scrutineer will check it. Garreth’s advice is to decide which kind of car you are building before you buy the seat, because it changes every other part.
Choosing the frame
We list direct fit frames for a wide range of cars from Sparco, Corbeau, Cobra and Planted Technology. They bolt to your car’s factory floor mounts and give the seat and runners a proper foundation, with no fabrication. For Sparco recliners, a Sparco frame, or another frame on the 345mm by 271mm pattern, is the simplest route. Cobra frames use a 291mm pattern, so they are not a direct match.
If you are not sure which frame suits your car, send us the make, model and year, and the seats you are fitting, and we will put the full set together.
What bolt pattern do Sparco reclining seats use?
Sparco’s R100, R333 and R500 are base mount seats on a 345mm by 271mm pattern.
Do Sparco runners fit OMP and Corbeau seats?
Yes, on base mount seats with the same 345mm by 271mm pattern.
How tight should the bolts be?
Tighten them evenly to the torque the frame and runner makers specify, using a torque wrench.
Are Sparco reclining seats FIA approved?
No. They are road and track seats, suited to road cars and non-competitive track days.
Do I need one runner kit per seat?
Yes. One kit covers one seat, or the twin kit covers a pair.
💬
The key partThe Sparco runner kit
Same 345mm by 271mm pattern as the seat and frame, so it all lines up.
Need a personal recommendation?
We're here to ensure you pick the right seat.
Contact us today.



