Call Garreth, Cameron & Jack: 0115 647 8650

FREE UK shipping on orders over £100.00 & FREE gifts on checkout

Your garage NewAdd your car and see the parts that fit
Useful Links
Your Account

Talk to us

Garreth, Cameron & Jack · Mon to Fri
Call 0115 647 8650Free advice on your build
Thanks, that’s with us. We reply the same working day.
That didn’t send. Please give us a call instead.

Useful Links

Quick Access

Want to chat?

Call Garreth, Cameron, Jack
Today On: 0115 647 8650
Click Here For Our Contact Form

 

 

Weetabix Truck With Cobra Seats And TRS Harnesses

From the archive, September 2024

Of all the vehicles we have supplied seats for, the Weetabix promotional truck is one of the most unusual. Built by Weetabix with the Daily Star and first reported in 2014, it is a V8 milk float in yellow and blue Weetabix livery, and we supplied the Cobra Monaco Pro bucket seats and blue TRS 4-point harnesses that went inside it.

It is a good example of proper motorsport seats going into something that is not a race car at all. A vehicle built to go much faster than any milk float should still needs to hold its driver in place, and a steel FIA seat with a full harness does exactly that.

  • A V8 Weetabix milk float built with the Daily Star, first reported in 2014
  • We supplied Cobra Monaco Pro FIA bucket seats
  • Paired with blue TRS 4-point FIA harnesses
  • The Monaco Pro is a steel seat, homologated to FIA 8855-1999
  • It can be base mounted or side mounted
A pair of black Cobra Monaco bucket seats with green Cobra logos in the GSM Performance showroom
Cobra Monaco seats in our showroom. These are not the seats from the Weetabix build.

The Weetabix truck

The truck was built for Weetabix and the Daily Star as a promotional vehicle: a milk float with a V8, bright yellow and blue Weetabix branding and flames down the sides. It was always going to be an eye-catching project.

What surprises most people is the inside. Behind the wheel sit Cobra Monaco Pro FIA bucket seats with blue TRS 4-point FIA harnesses, the same kit you would find in a club race car. For a vehicle built to go far faster than a milk float normally would, it made sense to hold the driver in properly.

The Cobra Monaco Pro seats we supplied

The Monaco Pro is a fixed-back seat for competition and fast road use, homologated to FIA 8855-1999. Most FIA seats at this level are composite; the Monaco is fully steel plated, with a solid back and base for intrusion protection. It has deep side support, an integral head pad and shoulder supports, and slots for a 4 or 6 point harness.

It can be base mounted or side mounted, which is unusual on an approved seat and useful on a build like this, where the floor is not a normal car floor.

A pair of black vinyl Cobra Monaco bucket seats with black and white houndstooth centre panels on the showroom floor
A pair of Cobra Monaco seats with houndstooth centres, showing how far the trim can be changed.

Our listing sizes the Monaco Pro for drivers under 6ft with a 32 to 36 inch waist, and it weighs 11.4kg, the honest cost of the steel plating. Cobra offers it in spacer fabric or soft grain vinyl, in one or two colours, with a wide choice of stitching and logo colours, so it can be matched to almost any livery.

We list a range of Monaco seats in different trims, approvals and widths, including versions for small cockpits, so there is one to suit most drivers and cars.

The TRS Magnum 4-point harnesses

The harnesses were TRS Magnum 4-point belts in blue. The Magnum uses 75mm (3 inch) webbing on the shoulder and lap straps, with a 140 gram composite aircraft rotary buckle on the right-hand lap strap. It is homologated to FIA 8854-1998 for saloon car use and comes with eyebolts and 7/16 inch UNF set-screws.

TRS harness straps in yellow, red, black, orange, grey, blue and green hanging on a wire display in the showroom
TRS harnesses in a range of webbing colours on our showroom display.

TRS introduced three small details that make a real difference in use: an intercom cable tab on the shoulder strap, thumb loops on the lower shoulder straps for easy adjustment, and Velcro patches on the outer lap straps so they stay on the seat when you climb in. The Magnum comes in a wide choice of webbing colours, which is how the truck got belts to match its blue livery.

Garreth’s advice when pairing a seat and harness is to check the seat’s slots suit the harness you want, which is why we sell the Monaco Pro with a matching TRS harness as a bundle. Our guide to fitting a motorsport harness covers the mounting.

Cobra Monaco Pro FIA bucket seats, which we supplied.

Blue TRS Magnum 4-point FIA harnesses, which we supplied.

Yes. It is homologated to FIA 8855-1999.

Yes. It can be base mounted or side mounted.

💬
The pairingMonaco Pro and TRS Magnum

A steel FIA seat and a 3 inch FIA harness that suit each other.

Need a personal recommendation?

We're here to ensure you pick the right seat. Contact us today.
Our showroom virtual walk through!
Have a walk around our showroom before you even buy your new seats. 
Our hands on experience, is what allows us to bring you our recommendations.
Free UK Shipping

On all orders above £100

Showroom

Try before you buy, by appointment

Delivery Tracking

Updates by email and text