“2 pairs – Sparco FIA Steel Side Mount Brackets” has been added to your basket. View basket
Free gift unlocked
Gift box is in your basket at no charge.
Installing Sparco Racing Seats In A Subaru WRX: What We Learned
Seat fitting guide
Dustin Williams posted a useful YouTube video of fitting Sparco Evo II bucket seats, Sparco harnesses and a harness bar to his 2015 Subaru WRX. It has been out for a while and some of the parts in it are no longer made, but it is still one of the clearer walkthroughs of a seat swap in this car.
Here is what the video shows, what has changed since, and the parts you would use to build a similar setup today.
- The video shows a 2015 Subaru WRX, the VA generation
- The Sparco Evo II in the video has since been replaced by the Evo QRT range
- Planted Technology bracket SB206 fits the 2015-on WRX and STI
- Stack with runners: frame, runner, belt mount if needed, side mounts, seat
- The Evo QRT seats are side mount only and take four or six-point harnesses

What is on this page
The video
The video follows the whole job, from taking out the factory seats to bolting in the Sparco seats, side mounts and sliding runners, then fitting a harness bar and harnesses. It shows the cockpit before and after, which makes it easy to see how the parts go together and how different the car looks once it is done.
Even if you are not fitting the same seat, the order of work and the way the fitting parts go together apply to most WRX seat swaps.
What the install shows
- The factory seat comes out with basic tools: four bolts and the airbag sensor plug.
- The side mounts set the seat’s height and tilt, depending on which holes you use.
- The sliders needed some adjusting to fit properly, a reminder that seat installs often need small tweaks.
- The harness bar and harnesses went in afterwards, with the factory belts kept for the road.
- The harness bar was the more involved part of the job, with some interior trim to remove.
Side mounts let you choose the seat’s pitch: front higher than the rear for a more reclined position, or flatter and more upright for a race position. It is worth trying a couple of settings before tightening everything down.
If you unplug the factory seat’s airbag or occupancy sensor, the car may show a warning light. Talk to a specialist about how to deal with that on your car.
The seat: from Evo II to Evo QRT
The seat in the video is the Sparco Evo II, which is no longer made. Its place in Sparco's range is now taken by the Evo QRT seats, built with Sparco's QRT resin transfer process for the fibreglass shell.
The Evo QRT comes in standard, L and XL shells, in velour, and the standard shell is also made in Sky vinyl. All are FIA 8855-1999 homologated, head and neck restraint friendly, side mount only, and take four and six-point harnesses.

The Evo L is the large shell, for drivers who find the standard Evo too narrow at the shoulders or hips. Some drivers also prefer the wider shell because a very tight seat can get in the way of small steering inputs. Garreth’s advice is to try both if you can, or send us your height and waist and we will suggest which shell suits you.
Building a similar setup today
The Sparco WRX frame in the video is no longer available, but you can build the same kind of setup with current parts:
- Planted Technology WRX bracket (part SB206), for the 2015-on WRX and STI. It bolts to the car’s own seat mounting points and is handed, so order two for both sides.
- Sparco FIA steel side mounts, which suit the Evo QRT seats.
- Sparco sliding runners on the 345mm pattern, if you want fore and aft adjustment.
- A harness and a way to mount it, such as a harness bar, if you are fitting harnesses.
With runners, the order from the floor up is: the vehicle bracket, the sliding runner, the seat belt mount if you are keeping the factory belt, the side mounts, then the seat. Our guide to base mount or side mount explains each layer.
Harnesses and harness bars
A harness is only as good as its mounting. The shoulder straps need to run back from the seat at the right angle to a proper anchor point, which in a car without a cage usually means a harness bar. The video shows the bar going in, and it was the most involved part of the job.
Our guide on how to fit a motorsport harness covers the angles and anchor points. If the car is used in competition, check the seat, harness and mountings with your scrutineer before the event.
How it changes the car
In the video, the difference is obvious: the seat holds the driver in place and the car feels more direct. There is more road feel and vibration than with the standard seats, which is part of the character of a fixed-back fibreglass seat, but with the position set up well it stays comfortable enough for the road.
If you have a WRX or another project and want help putting the right seat, mounts and bracket together, send us the car’s year and your measurements, or come and sit in the seats in our showroom.
Is the Sparco Evo II still made?
No. Its place in Sparco’s range is taken by the Evo QRT seats, in standard, L and XL shells.
Which bracket fits a 2015-on Subaru WRX?
The Planted Technology SB206 bracket fits the 2015-on WRX and STI, and bolts to the factory seat mounting points.
Can I keep the factory seat belt with a bucket seat in a WRX?
Yes, with a sliding runner and a seat belt mount in the stack so the buckle moves with the seat.
Do Sparco Evo QRT seats need side mounts?
Yes. They are side mount only and suit Sparco’s FIA steel side mounts.
💬
The current equivalentSparco Evo QRT
The seat that took the Evo II's place, on a Planted WRX bracket.
Need a personal recommendation?
We're here to ensure you pick the right seat.
Contact us today.



