Audi 80 B3 Type 89 Bucket Seat Guide
A supported seat change for the aerodynamic B3 saloon
The B3 Audi 80 brought a smoother, more aerodynamic body to the range in 1986. Audi called this generation Type 89. For a road-and-track build, the seat decision can range from a restrained retro bucket to a reclining sport seat that gives you more backrest adjustment.
Garreth would start by trying the RRS alongside the GT8, with the way you use the car deciding the shortlist. Cameron would confirm Type 89 and the original floor fittings, then pair the chosen Corbeau base-mounted seat with the kit and its included runners. Send photographs if a previous conversion has changed the mounting area.

At a glance
- Vehicle kit: Corbeau Audi 80/90 Type 89/B4, with Audi 80 B3 Type 89 identified on the enquiry.
- Seat route: Corbeau base-mounted Classic buckets or Sportline recliners.
- Double-locking sliding runners are included with the subframe kit.
- One kit per seat position; specify the seat model and physical side.
- Measure the complete assembly for headroom, controls and fore-and-aft travel.
The Corbeau fitting kit for Audi 80 B3 Type 89
Our Corbeau Audi 80/90 fitting-kit listing names Type 89/B4. For this guide, the relevant application is the Audi 80 B3, also known as Type 89.
Keep B3 or Type 89 on the enquiry alongside the year, steering side and physical seat position. The older Type 81/85 car has its own fitting kit. A badge or registration year on its own can leave the wrong generation on the order, so include a photograph of the car if you are unsure.
Corbeau designs this kit family around its base-mounted Classic buckets and Sportline recliners. Choose the exact seat model and width with the frame. One kit serves one seat position.
Use the runners supplied with the kit
Double-locking sliding runners are included with Corbeau’s subframe kits. Use the supplied runners as part of the vehicle kit; adding another universal slider is not a routine step in this assembly. Depending on the application, Corbeau supplies a full replacement frame or a bracket-and-runner arrangement, so confirm the supplied layout with the seat you are ordering.
- Fit the vehicle-specific kit at the car’s original mounting positions, following its supplied instructions.
- Attach the compatible base-mounted seat through the kit’s included runners using the specified hardware.
- Trial-position the complete assembly for pedal reach, steering-wheel reach and headroom.
- Operate the runner handle and check its locking action and full travel with the surrounding trim in place.
Use the current kit and seat instructions for the fixings and final tightening. Corbeau designs this route around base-mounted seats; a side-mounted shell needs its own supported mounting arrangement.
Three Corbeau retro buckets to try
The GT8 would be Garreth’s fixed-bucket starting point for a B3 being given a period track-day interior. Its high back, shoulder openings and eyelet finish give it a different feel from a lower retro seat. Try how its backrest supports you before selecting it.
The Classic offers a simpler trim style, with Standard and Wide cushions plus material, piping and headrest choices. The Alpine adds quilted detailing and a cloth centre in Corbeau’s current specification. Cameron would compare the chosen cushion width with the space beside the B3’s centre tunnel, then check the upper seat against the door trim.
-
From £348.00 Incl. VATFrom £290.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £468.00 Incl. VATFrom £390.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £510.00 Incl. VATFrom £425.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
The Sportline RRS low-base recliner
The Sportline RRS low-base seat keeps an adjustable backrest and integrated headrest within the Corbeau base-mount route. It is the option Garreth would try if the Audi still does longer road journeys. Sit with the backrest set for your steering and pedal reach, then check whether the cushion supports your legs comfortably.
Allow room for the recliner control and runner release through the adjustment you need. The installed height comes from the seat, kit and runners together; the low-base name alone does not give a measurement relative to the Audi’s original seat.
-
From £498.00 Incl. VATFrom £415.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Compare the Classic and GT8 base sizes
The Classic Standard base measures 470mm wide by 550mm deep in Corbeau’s current drawing, while the Wide is 500mm by 550mm. The GT8 base is 490mm by 540mm. The three rectangles show those A and B dimensions at one scale so you can compare the bases directly.
Corbeau lists 700mm overall height on the Classic drawing and 930mm on the GT8 drawing. These figures describe the seats, with the mounting hardware and chosen headrest configuration checked separately. Use the full assembly when checking your headroom in the car.
Cameron would measure the room at the cushion and again around the shoulders. Check the bolster and control clearance beside the door and centre tunnel, then try the adjustment needed by everyone who drives the car.
A four-point harness option for the planned seat
The TRS Clubman clip-in four-point uses shoulder and lap straps with 50mm webbing and a push-button buckle. Discuss the end fittings and intended anchor arrangement with the seat choice. Its clip-in ends are useful where the belt needs to be removed between uses.
Choose the seat version with its belt path in mind, including the Classic’s optional harness grommets and headrest. Shoulder openings still need to line up with the driver once the complete seat assembly is positioned. Send photographs of the space behind the seats and follow the harness maker’s current instructions for the anchors and any permitted wrap-around routing.
-
From £120.00 Incl. VATFrom £100.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
Details to send with the fitting enquiry
Send Audi 80 B3/Type 89, the year, body details and steering side, plus the physical left or right seat position. Include the chosen seat and width, your height and waist, and whether several drivers need adjustment. Photographs of the existing floor connections and tunnel let Cameron check any previous conversion before the new fitting parts are ordered.
Common questions
The Audi 80 B3 Type 89 application. Identify the chassis, year and body details with the enquiry so the Corbeau Type 89/B4 listing is matched to your car.
Double-locking runners are included with this Corbeau kit family. Confirm the supplied frame or bracket layout with your exact seat and vehicle details.
One fitting kit serves one seat position. Specify both sides and the seat models if you are changing the pair.
The Corbeau base-mounted Classic range, including the Classic, Alpine and GT8 choices shown here. Confirm the actual seat version and width with the kit.
Corbeau specifies this kit family for base-mounted seats. A side-mounted competition shell needs a separately supported mounting arrangement.
Measure the seat with its vehicle kit and included runners, positioned for your pedal and steering-wheel reach. Check headroom and the space for the backrest, bolsters and adjustment controls.
Include the exact body, chassis details and photographs of the existing mounts. A shared model name or similar appearance does not establish every body or market application.
Garreth’s top tip
I would try the RRS if this is still a regularly used road car, with the GT8 alongside it for a firmer fixed-back choice. Keep the trim decision until you have found the shape that suits you. Both can work visually with the B3, but they feel different to sit in.
Cameron’s fitting view
I would identify Type 89 at the start and check the floor photographs if the car has been modified before. The kit includes runners, so I would work through the full assembly height and travel with the seat you actually want. Check the door-side bolster and the recliner controls before finalising the position.
Plan your Audi 80 B3 Type 89 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Fitting references: Corbeau subframe and included-runner guidance. Seat specifications and drawings: Classic, Alpine, GT8 and RRS low base. Harness reference: TRS Clubman four-point. Model background: Audi Tradition’s 2026 model history.





