Alfa Romeo 146 Bucket Seat Guide
Keep the five-door Alfa useful
The 146’s separate rear doors make a fixed-back front seat easier to live with when passengers still use the rear bench, though the driving position needs to suit the person using it every day.
Cameron would check the original seat runners before choosing the mounting parts. Garreth would then compare the support of a fixed bucket with the backrest adjustment of a reclining seat. The Sparco 146 frame is the vehicle-specific starting point for both enquiries.

At a glance
- Vehicle: five-door Alfa Romeo 146, Tipo 930. Sparco’s application sheet lists December 1994 to September 2000.
- Current fitting frame: Sparco 00499085 family, sold singly with driver or passenger side selection.
- Seat-side base pattern: 345mm across and 271mm front to rear.
- Runners: inspect the original assembly; the manufacturer application uses the original-runner arrangement.
- Seat shortlist: base-mounted buckets and recliners, with side mounts added where the chosen shell requires them.
The Sparco fitting frame for the 146
Our Alfa Romeo 146 frame is listed under the 00499085 part family. Select the correct side for the car and order one frame per seat. A pair of seats needs a driver-side and passenger-side arrangement, checked against the steering side of your particular Alfa.
Sparco’s application sheet gives the same base part family for the 145 and 146. That is useful evidence for the frame application, but the seat choice still needs checking in your five-door cabin. We would not transfer an assumed seat height or door clearance from a photograph of somebody else’s 145.
The frame’s 345mm x 271mm seat-side pattern describes the fixing above the frame, separate from the Alfa floor measurements.
-
From £87.00 Incl. VATFrom £72.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Check the original runners before adding sliders
Sparco marks the 146 application as “Serie”. The key in its application sheet describes the original sliding rails beneath the Sparco base for a tuning installation. The same key gives a separate competition qualification, so this archived road-use arrangement should not be treated as a competition mounting specification.
Cameron would want a clear photograph of the current seat base and runners before completing the order, including any fittings that have replaced the originals.
A universal slider on the matching bolt pattern is a component to consider when the complete mounting arrangement calls for it. It is not an automatic extra for this car. Garreth would keep the order to the fittings that the actual installation needs.
For a competition build, give us the seat model and the requirements for the intended event so the appropriate complete mounting route can be checked.
345mm x 271mm, drawn to scale
The four bolt centres below have the same scale in both directions. The frame outline is schematic. These dimensions agree between Sparco’s application sheet and the current 146 product listing.
A base-mounted seat needs a matching connection through the assembly. A side-mounted shell needs a suitable pair of side mounts above the vehicle frame, with the mount bases and any sliders checked together. Measure the finished position in the car before settling on either route.
Fixed-back buckets to compare
The Sparco Sprint, Sprint L and OMP TRS-X all have base and side mounting options in their current listings. They offer different driver-size starting points, which is more useful than choosing a shell from its photograph alone.
OMP’s catalogue gives 345mm x 270mm as its Type Y bottom-fixing reference. Have us check the TRS-X mounting drawing against the complete rail and frame arrangement before ordering. The Sprint versions also need their current drawings and fasteners checked for the selected assembly.
- Sparco Sprint: the current waist guide is 32 to 36 inches.
- Sparco Sprint L: the current waist guide is 40 to 42 inches. Check the larger shell against the door and centre tunnel.
- OMP TRS-X: the listing covers 28 to 32 and 32 to 36 inch waist ranges. Confirm the version for your measurements.
A five-door body gives rear passengers their own entrance, but the seat’s shoulder wings can still affect space behind the driver. Cameron would check that alongside the base width and your headroom.
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Reclining choices for regular road use
The Sparco R100, R333 and GT all list the frame’s 345mm x 271mm base pattern. They are mounting candidates to compare with the original-runner arrangement and the available cabin space.
The R100 has broader listed driver-size guidance. The R333 and GT listings give a 32 to 36 inch waist guide and an under-six-foot height guide. Try the backrest shape and cushion before deciding between them; the published ranges are a shortlist, not a measurement of your Alfa.
For a car used by more than one driver, Garreth would give the adjustment range a proper trial. Cameron would check the recliner controls and runner handle with the door shut, then check both drivers’ reach to the wheel and pedals.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £449.47 Incl. VATFrom £374.56 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
£562.10Original price was: £562.10.£505.90Current price is: £505.90. Incl. VAT£468.42Original price was: £468.42.£421.58Current price is: £421.58. Excl. VATPayPal CreditKlarna ReadyAdd to basket
Harness options and the mounting behind the seat
Our R100, R333 and GT listings specify four-point harness compatibility. The bucket shortlist has six-point compatibility listed, with four-point compatibility also stated for the TRS-X. A seat’s harness openings are only part of the selection; the car needs a suitable mounting arrangement for the particular belt.
The TRS Clubman clip-in and bolt-in four-point belts differ in their end fittings. Both listings say they are not HANS compatible. The Schroth Profi 3×2 is a six-point, HANS-friendly option for a suitable seat and installation, including the required crotch-strap provision.
Send photographs of the space behind the front seats before choosing the belt. Follow its manufacturer’s mounting instructions. A cage tube or harness bar is a mounting location only where that component’s maker specifies it.
-
From £120.00 Incl. VATFrom £100.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £81.00 Incl. VATFrom £67.50 Excl. VATPayPal CreditAmazing valueSpeed+ ServiceSelect options This product has multiple variants. The options may be chosen on the product page
-
From £444.01 Incl. VATFrom £370.01 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Measurements to take before ordering
Check the widest part of the proposed seat at the base, hips and shoulders against the cabin. Then check your seated height in the complete assembly. The combination of frame, runners and seat determines where you sit; changing the frame alone does not establish a lower position.
- Close the door and allow space for the recliner controls or side-mount hardware.
- Check pedal operation and steering-wheel reach throughout the adjustment you actually need.
- If the rear bench remains, check the space behind the front seat in its normal driving position.
- For two regular drivers, repeat the checks at both preferred positions.
Common questions
The Sparco Alfa Romeo 146 direct-fit subframe, from the 00499085 part family. It is sold singly with side options, so confirm the side and steering arrangement when ordering.
Sparco’s application sheet lists the 145 and 146 under the same base part family. We keep separate vehicle guides because the body access and individual cabin installation still matter.
Check what is already in the car first. Sparco specifies original sliding rails beneath this base for the tuning arrangement. We would confirm the current frame and proposed seat together before adding a separate slider.
It needs compatible side mounts above the vehicle frame and a confirmed complete installation. Send the shell model and the intended use so the mounts, any runner and the finished position can be checked together.
Yes. You still gain backrest adjustment even though rear passengers have separate doors. Check the controls, runner travel and seat dimensions in your own cabin.
The car’s year, steering side, photographs of the original or current runners, the proposed seat model and your height and waist. Include whether the rear bench stays and whether the car is used for competition.
Garreth’s top tip
For a 146 that still does regular journeys, I would try the reclining options before deciding on a fixed shell. Keep the seat support you want alongside the adjustment that makes the car comfortable to use.
Cameron’s fitting view
I would start underneath the seat. A photograph of the original runners tells us which parts need checking, and avoids building an order around a slider the car may already have.
Plan your Alfa 146 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Technical reference: Sparco application sheet, pages 14 and 19. The archived sheet supplies the pattern and original-runner reference; confirm the current parts for your particular car when ordering. For the OMP mounting reference, see its 2024 catalogue, printed pages 68 and 69.









