Call Garreth, Cameron & Jack: 0115 647 8650

FREE UK shipping on orders over £100.00 & FREE gifts on checkout

Your garage NewAdd your car and see the parts that fit
Useful Links
Your Account

Talk to us

Garreth, Cameron & Jack · Mon to Fri
Call 0115 647 8650Free advice on your build
Thanks, that’s with us. We reply the same working day.
That didn’t send. Please give us a call instead.

Useful Links

Quick Access

Want to chat?

Call Garreth, Cameron, Jack
Today On: 0115 647 8650
Click Here For Our Contact Form

 

 

Citroen ZX Three-Door Bucket Seat Guide

Plan the ZX’s seat, runner and base together

For a ZX three-door seat enquiry, we start with Sparco base 00499054 and the seat you want above it. The ZX arrived in 1991, with three-door versions following in autumn 1992. Keep the body style on the enquiry: our fitting listing specifically covers the three-door.

Garreth would try a Sprint fixed-back seat alongside a reclining R100 before choosing the direction for the car. Cameron would put the runner reference and mounting arrangement beside that choice. Sparco’s fitting sheet identifies a particular assembly, so the parts below the cushion deserve the same attention as the seat itself.

Front three-quarter view of an illustrative modified dark green Citroen ZX three-door with bronze wheels, black racing bucket seats and orange harnesses visible through the windscreen
Illustrative modified Citroen ZX three-door, not a customer installation.

At a glance

  • Listed vehicle base: Sparco 00499054 for the Citroen ZX three-door; one seat position per frame.
  • Sparco’s archived application table identifies ZX type N2 with runner 00493 and 345mm x 271mm seat-side centres.
  • The exact 00499054 fitting sheet includes a separate inner-side belt attachment bracket and specifies assembly orientation.
  • Our current runner card is 0049306. Sparco lists that KR runner separately from 00493, so confirm the required supplied reference.
  • Compare Sprint fixed-back choices with R100 and R333 recliners, then trial the complete position and rear-seat access.

Sparco 00499054 for the three-door ZX

Our ZX frame listing names the three-door and carries reference 00499054. Sparco’s 2018 application table independently links that number to ZX type N2. It also identifies 00493 as the runner for the application.

The catalogue gives a January 1991 to March 1998 ZX family range, which begins before the three-door’s introduction. Use the actual body and vehicle details when checking the application. This guide follows the narrower three-door scope of our listing; the family dates do not establish a five-door or estate installation.

Select the physical seating side in the order and tell us whether you are fitting one seat or both. Our shop offers RHD driver and passenger choices, while the manufacturer document uses the same base reference. Cameron would confirm the current supplied arrangement for that position, including the separate bracket shown in Sparco’s drawing.

Specify the runner reference with the ZX base

Sparco’s 00499054 fitting sheet and vehicle table name runner 00493. The runner card shown here carries 0049306, described as Slide Runners KR in Sparco’s 2025 catalogue. Both catalogue entries give 271mm longitudinal spacing, but they remain separate references.

Cameron would check the current supplied runner and its connection to the ZX base before completing the order. Ask specifically for the 00499054 assembly and the runner it requires. A matching longitudinal measurement alone cannot confirm the lower fixing, handle position or full assembly.

The original sheet shows the runner fitted to the seat before that assembly is attached to the vehicle base. Follow the orientation in the instructions supplied with the actual parts. Trial the release and locking action with the driver seated and check the travel needed by everyone who uses the car.

Compare Sprint, Sprint Sky and Sprint L

The Sprint family gives a tubular-frame fixed-back option for a focused ZX interior. Standard Sprint fabric and Sprint Sky upholstery offer different surfaces to try, while Sprint L is the larger version. Garreth would choose the cushion and backrest shape before settling on the finish.

Sparco’s 2025 catalogue identifies base mounting at 271mm x 345mm and a 290mm side-fixing spacing for the illustrated Sprint and Sprint Sky models. Confirm the exact seat version and its instructions with the order. A base-mounted arrangement and a side-mounted arrangement have different parts beneath the cushion.

Try the seat for hip support and shoulder position, then measure its outer shape in the car. Include the door trim, tunnel and buckle area. A seat-size label or waist range cannot establish clearance in a ZX that may already have a changed interior.

Choose the seat connection before adding side mounts

These Sparco steel side mounts are an option to discuss for a seat using lateral fixings. They add a connection between the shell and the lower assembly. Confirm the side-mount reference, hole positions and runner connection with the exact seat.

A Sprint fitted through its lower mounting points does not automatically require a pair of side mounts as well. Cameron would draw out each connection on the parts list so the assembly is clear. A different competition shell needs its own mounting instructions and matching supports.

R100, R100 vinyl and R333 reclining choices

The R100 fabric and vinyl versions give you a reclining backrest to compare with the fixed Sprint. The R333 offers a different cushion and bolster shape to try. Garreth would judge support, entry and exit in person, especially if the ZX still does regular road journeys.

Sparco’s 2025 catalogue gives the R100 family and R333 271mm x 345mm lower fixings. Check the exact supplied seat reference, runner and ZX base together. Those centres establish one part of the mounting enquiry without promising how the whole seat sits in the cabin.

Move the backrest through the range you need and check that the adjustment levers remain reachable. On a three-door, try the route into the rear before choosing the finished arrangement. A reclining backrest and a sliding runner each provide their own movement; neither alone proves the access you want.

The 345mm x 271mm seat-side pattern

The diagram draws the mounting centres at one scale, using the seat-side reference in Sparco’s ZX application table. These centres are also the lower-fixing dimensions given for the R100 and R333 in the 2025 catalogue. Measure the actual seat and runner connection before assembly.

The outer frame shape is schematic. This drawing gives neither the ZX floor-hole pattern nor the outside width of a seat. Check the shell, controls and all lower fittings separately when measuring cabin clearance and finished cushion height.

Seat-side bolt centres 345 by 271 millimetres, drawn to scale345mm across271mm front to rearSeat-side bolt centres; outer frame outline is schematic

Try rear access with the chosen front-seat arrangement

If passengers still use the rear, make access part of the initial seat choice. Trial the front seat in the position the driver needs, then operate the available slide and backrest movement. Keep any proposed harness layout in the same discussion.

Sparco also catalogues a separate tilt-forward accessory, but its existence does not establish a complete ZX combination. Cameron would check any additional mechanism against the chosen base, runner and seat before recommending it. Every extra component changes the assembly that must be trialled in the car.

Choose harnesses around the seat and attachment layout

The four-point examples and six-point competition option shown here suit different belt layouts. Start with the intended use and the exact seat’s belt openings. A recliner with shoulder openings should not be assumed to accept the same arrangement as a fixed competition bucket.

Cameron would check the belt maker’s routing instructions, available attachments and buckle access in the actual car. Include rear passengers if that is part of the build. The ZX seat base and its original-belt bracket do not establish harness attachment positions.

Follow the base instructions and trial the driving position

Sparco’s dated 00499054 sheet shows the vehicle base, an inner-side belt attachment bracket and the runner-and-seat assembly. It specifies the base and runner-handle orientation. Use the current instructions supplied with your exact kit for the work, including its required fixings.

Record the car’s year, three-door body, physical seat position and any changes to the existing mounts. Photograph the current arrangement before selecting the parts. Cameron would compare those details with the proposed seat and the components actually supplied.

Trial the completed position with the driver: wheel and pedal reach, headroom, buckle access and movement through the required runner travel. Check clearance with the door closed and the controls in use. Garreth would finish by trying normal entry and exit before the upholstery decision is settled.

Common questions

We list Sparco 00499054, specifically for the three-door. Sparco’s archived application table also links 00499054 to ZX type N2. Confirm the year, physical seating side and exact supplied assembly with the chosen seat.

Our fitting listing specifies the three-door. The maker’s wider ZX family dates do not establish another body style for this listing. Send the full vehicle details for a separate application check.

The 00499054 fitting sheet and archived application table name 00493. Our current runner card carries 0049306, a separate KR entry in Sparco’s catalogue. Confirm the required current runner and its connection before ordering; shared 271mm longitudinal spacing is insufficient on its own.

Sparco’s 2025 catalogue identifies 271mm x 345mm base fixings for the illustrated Sprint and Sprint Sky models, alongside a side-mount option. Confirm the exact seat version and its supplied instructions. Choose the complete base-mounted or side-mounted assembly before adding fittings.

The manufacturer catalogue identifies lower fixings for those reclining families. Match the exact seat to its runner and ZX base. Side mounts are selected for a seat using lateral fixings, not added automatically to every seat assembly.

Trial the whole seat, runner and base with the driver. The cushion and every lower fitting affect the finished height. The 345mm x 271mm pattern describes mounting centres and cannot predict a height change.

Try the required route into the rear with the proposed seat position, slide and backrest movement. Include any harness arrangement. Confirm an additional access mechanism as part of the complete assembly before selecting it.

Garreth’s top tip

Garreth would try the Sprint and R100 first, with the ZX’s actual use in mind. Sit long enough to compare support and getting over the side bolster, then try a different size or the R333 if you want another shape. Choose the finish once you have found the seat you want to sit in.

Cameron’s fitting view

Cameron would put 00499054, the exact seat and the required runner reference on one parts list. He would check the three-door body, physical seat position and supplied belt bracket, then trial the complete position. The distinction between 00493 and 0049306 stays on that enquiry until the actual assembly is confirmed.

Plan your Citroen ZX three-door seat change

Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.

Back to the Car Seat Selector guide.

Sources: Sparco’s 2018 vehicle application catalogue; Sparco 00499054 fitting sheet, 13 May 2002; Sparco’s 2025 catalogue, printed pages 178, 324, 326 and 327; Citroën’s ZX model history. These documents establish application and component references; use the instructions supplied with the current kit for installation.

Free UK Shipping

On all orders above £100

Showroom

Try before you buy, by appointment

Delivery Tracking

Updates by email and text