Audi 80 B4 Bucket Seat Guide
Bucket seats and recliners for the fourth-generation Audi 80
Audi launched the fourth-generation 80 in September 1991, with a longer wheelbase and a revised rear axle. It can look close to the preceding B3 at first glance. Keep B4 on the fitting enquiry before we discuss the seat.
Garreth would compare a reclining Sportline seat with a fixed high-backed bucket, depending on how much road use the car gets. Cameron would ask for the body details and photographs of the current mounts. That gives us the starting point for the Corbeau kit and its included runners.

At a glance
- Vehicle kit: Corbeau Audi 80/90 Type 89/B4, with Audi 80 B4 identified on the enquiry.
- Seat route: Corbeau base-mounted Classic buckets or Sportline recliners.
- Double-locking sliding runners are included with the subframe kit.
- One kit per seat position; specify the seat model and physical side.
- Measure the complete assembly for headroom, controls and fore-and-aft travel.
The Corbeau fitting kit for Audi 80 B4
The fitting kit shown here is our Corbeau Audi 80/90 Type 89/B4 application. Keep B4, the year and body details together when ordering it for this generation of Audi 80.
Tell us which physical seat position you are changing and whether the car is right- or left-hand drive. Include photographs where the floor, original fittings or centre console have already been altered. A car that has had several interiors fitted needs that check before the replacement parts are chosen.
Corbeau’s supported seat route uses its base-mounted Classic buckets and Sportline recliners. Each kit is for one seat position, with the exact seat model confirmed alongside the vehicle details.
Use the runners supplied with the kit
Double-locking sliding runners are included with Corbeau’s subframe kits. Use the supplied runners as part of the vehicle kit; adding another universal slider is not a routine step in this assembly. Depending on the application, Corbeau supplies a full replacement frame or a bracket-and-runner arrangement, so confirm the supplied layout with the seat you are ordering.
- Fit the vehicle-specific kit at the car’s original mounting positions, following its supplied instructions.
- Attach the compatible base-mounted seat through the kit’s included runners using the specified hardware.
- Trial-position the complete assembly for pedal reach, steering-wheel reach and headroom.
- Operate the runner handle and check its locking action and full travel with the surrounding trim in place.
Use the current kit and seat instructions for the fixings and final tightening. Corbeau designs this route around base-mounted seats; a side-mounted shell needs its own supported mounting arrangement.
Three Corbeau retro buckets to try
For a B4 with a deliberately retro interior, Garreth would try the GT8 high-backed bucket first. It has shoulder openings and an eyelet trim option, with a fixed backrest that needs to suit your driving posture. Check the space around its upper sides as well as the cushion.
The Classic gives you Standard and Wide versions with a simpler trim style, plus piping and headrest options. The Alpine adds quilted detailing to its cloth-centre and vinyl-outer combination. Cameron would check the width at the tunnel and door with the intended seat position set, particularly when a larger cushion is being considered.
-
From £348.00 Incl. VATFrom £290.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £468.00 Incl. VATFrom £390.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £510.00 Incl. VATFrom £425.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
The Sportline RRS low-base recliner
The RRS low-base Sportline seat is the reclining choice in this guide. Its adjustable backrest and integrated headrest suit a different brief from the fixed retro buckets. Garreth would try it for a B4 that spends more time on road journeys, checking the cushion support with the backrest in a natural driving position.
The seat’s low-base designation identifies the version, so measure the whole fitting assembly when checking the resulting headroom. Leave space to operate its controls and to reach every runner position you expect to use.
-
From £498.00 Incl. VATFrom £415.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Compare the Classic and GT8 base sizes
The Classic Standard base measures 470mm wide by 550mm deep in Corbeau’s current drawing, while the Wide is 500mm by 550mm. The GT8 base is 490mm by 540mm. The three rectangles show those A and B dimensions at one scale so you can compare the bases directly.
Corbeau lists 700mm overall height on the Classic drawing and 930mm on the GT8 drawing. These figures describe the seats, with the mounting hardware and chosen headrest configuration checked separately. Use the full assembly when checking your headroom in the car.
Cameron would measure the room at the cushion and again around the shoulders. Check the bolster and control clearance beside the door and centre tunnel, then try the adjustment needed by everyone who drives the car.
A four-point harness option for the planned seat
The TRS Clubman clip-in four-point uses shoulder and lap straps with 50mm webbing and a push-button buckle. Discuss the end fittings and intended anchor arrangement with the seat choice. Its clip-in ends are useful where the belt needs to be removed between uses.
Choose the seat version with its belt path in mind, including the Classic’s optional harness grommets and headrest. Shoulder openings still need to line up with the driver once the complete seat assembly is positioned. Send photographs of the space behind the seats and follow the harness maker’s current instructions for the anchors and any permitted wrap-around routing.
-
From £120.00 Incl. VATFrom £100.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
Details to send with the fitting enquiry
Include Audi 80 B4, year, exact body, steering side and the physical left or right seat position. Add the seat model and width, your height and waist, and photographs of the floor fittings if they have been altered. Tell us whether the rear seating and luggage area are staying in use so the seat adjustment and any harness routing can be discussed together.
Common questions
The Audi 80 B4 application. Identify the chassis, year and body details with the enquiry so the Corbeau Type 89/B4 listing is matched to your car.
Double-locking runners are included with this Corbeau kit family. Confirm the supplied frame or bracket layout with your exact seat and vehicle details.
One fitting kit serves one seat position. Specify both sides and the seat models if you are changing the pair.
The Corbeau base-mounted Classic range, including the Classic, Alpine and GT8 choices shown here. Confirm the actual seat version and width with the kit.
Corbeau specifies this kit family for base-mounted seats. A side-mounted competition shell needs a separately supported mounting arrangement.
Measure the seat with its vehicle kit and included runners, positioned for your pedal and steering-wheel reach. Check headroom and the space for the backrest, bolsters and adjustment controls.
Include the exact body, chassis details and photographs of the existing mounts. A shared model name or similar appearance does not establish every body or market application.
Garreth’s top tip
I would sit in the RRS before choosing a seat for a B4 used on longer trips. If the interior is being built around a period track-day look, I would put the GT8 beside it on the shortlist. Choose the support shape and adjustment first, then match the trim to the rest of the cabin.
Cameron’s fitting view
I would put B4 and the exact body on the enquiry, then check the existing mounts and the complete height with the chosen seat. The kit already includes its runners. I would also check access to the recliner controls and the clearance beside the console through the travel you need.
Plan your Audi 80 B4 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Fitting references: Corbeau subframe and included-runner guidance. Seat specifications and drawings: Classic, Alpine, GT8 and RRS low base. Harness reference: TRS Clubman four-point. Model background: Volkswagen Group’s 1991 annual report.





