Audi 80 Type 81/85 Bucket Seat Guide
A seat conversion for the boxy Audi 80
Keeping the older Audi 80 interior looking right is often part of the seat decision. Its square-edged saloon body suits a restrained build, and the choice here runs from a simple retro bucket to a reclining sport seat. Garreth would begin with the Classic or high-backed GT8 for a period-looking interior. Cameron would confirm Type 81/85 and the seat position first, then match the Corbeau kit to the exact base-mounted seat.

At a glance
- Vehicle fitting kit: Corbeau Audi 80/90 Type 81/85.
- Seat route: Corbeau base-mounted Classic buckets or Sportline recliners.
- Double-locking sliding runners are included with the subframe kit.
- One kit per seat position; specify the seat model and physical side.
- Measure the complete assembly for headroom, controls and fore-and-aft travel.
The Corbeau Type 81/85 fitting kit
Our listed Corbeau Audi 80/90 kit names Type 81/85 explicitly, which is the vehicle application used in this Audi 80 guide.
Tell us the year, body, steering side and whether you are changing the left or right seat. Photograph the existing floor fittings if an earlier owner has changed them. Keep the chassis type on the enquiry so the later Type 89/B4 listing stays a separate application. The kit is intended for Corbeau base-mounted Classic buckets and Sportline recliners. One kit serves one seat position; the order needs the exact seat model as well as the car details.
Use the runners supplied with the kit
Corbeau includes double-locking runners with its subframe kits. Keep them with the vehicle-specific brackets when planning the order; an extra universal slider is not a routine addition to this route. The kit can take the form of a complete replacement frame or brackets with runners, depending on the application. Confirm the supplied layout for your seat and car before installation.
- Assembly route: original vehicle mounting points, vehicle-specific Corbeau kit with its included runners, compatible base-mounted seat.
- Trial-position the assembly to check pedal reach, steering-wheel reach and headroom.
- Check the runner handle, locking action and full travel with surrounding trim in place.
Use the instructions supplied with the actual kit and seat for the hardware and final tightening. This Corbeau kit family is designed around base fixings; a side-mounted competition shell needs its own supported fitting route.
Three Corbeau retro buckets to try
The Classic gives Garreth a simple vinyl or leather seat to start with, with piping and headrest choices to suit the surrounding trim. Standard and Wide versions let you compare the cushion width before ordering. The Alpine adds quilted detailing, with a cloth centre and vinyl outer on Corbeau’s current specification. It also has two widths and a headrest option.
The GT8 is the high-backed fixed bucket in this group. Its eyelet finish and shoulder openings suit a more focused period build. Cameron would try the backrest shape and check its upper clearance in the Audi before settling on it.
-
From £348.00 Incl. VATFrom £290.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £468.00 Incl. VATFrom £390.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £510.00 Incl. VATFrom £425.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
The Sportline RRS low-base recliner
The RRS low-base seat adds backrest adjustment and an integrated headrest. It is part of Corbeau’s base-mounted Sportline range, so it follows the kit route described here. Garreth would try this if the Audi sees longer road journeys and you want to change the backrest angle. Check the position of its controls beside the tunnel and door trim.
The low-base name describes this seat version, so measure the finished assembly in the car before expecting a particular change in driving height.
-
From £498.00 Incl. VATFrom £415.00 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Compare the Classic and GT8 base sizes
Corbeau’s current drawings give the Classic Standard a 470mm outer base width and 550mm base depth. The Wide is 500mm across with the same 550mm depth. The GT8 base is 490mm wide and 540mm deep.
The rectangles use those base dimensions at the same scale. They help compare the space occupied around the cushion; they do not show the Audi floor fixings or establish cabin fit.
The Classic drawing lists 700mm overall height, while the GT8 drawing lists 930mm. These seat measurements exclude the mounting assembly. Check the actual headrest configuration, upper bolsters and headroom with the seat positioned for you.
Cameron would measure the space between the tunnel and door, then repeat the check at shoulder height. Use your normal driving posture and include the kit and runners when measuring the installed position.
A four-point harness option for the planned seat
The TRS Clubman clip-in four-point is an option to discuss with the seat and intended anchor arrangement. Its shoulder and lap straps use 50mm webbing, with clip-in ends and a push-button buckle. Check the belt path on the exact seat version. Classic headrest and harness-grommet choices need deciding with the order, and the GT8’s shoulder openings still need to line up with the driver.
Send photographs of the area behind the seats so we can discuss the shoulder routing and anchor positions. Follow the harness maker’s current fitting instructions, including any permitted wrap-around arrangement.
-
From £120.00 Incl. VATFrom £100.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
Details to send with the fitting enquiry
Include Audi 80 Type 81/85, year, body details, steering side and the physical left or right seat position. Add the exact seat model and width, your height and waist, and whether one driver or several will use the car. Photograph the original mounts and any previous conversion. Garreth can then help narrow the seat choice, with Cameron checking the fitting parts and adjustment needed for the complete order.
Common questions
The Audi 80 Type 81/85 application named on our Corbeau Audi 80/90 fitting kit. Give us the exact year and body details with the chassis type when ordering.
Yes. Corbeau specifies double-locking runners with its subframe kits. Confirm the supplied kit layout with the exact seat and vehicle details.
Each fitting kit serves one seat position. Include both positions and the seat models if you are converting the pair.
Corbeau’s base-mounted Classic range, including the Classic, Alpine and GT8 options shown here. Confirm the seat version and width with the order.
Corbeau specifies this kit family for base-mounted seats. A side-mounted shell needs a separately supported fitting arrangement.
The installed height depends on the seat, fitting kit and runners together. Measure the finished assembly in the car before expecting a particular height change.
Those details need their own application check. This guide follows the explicit Type 81/85 listing; send the body and chassis information if the car differs.
Garreth’s top tip
I would try the Classic first if the rest of the Audi 80 interior is staying close to its original style. The GT8 is worth sitting in alongside it if you want a taller backrest and a more purposeful appearance. Choose the width around your hips before choosing the trim.
Cameron’s fitting view
I would ask for Type 81/85, the physical seat position and a photograph of the existing mountings. With the seat identified, we can check the kit, included runners and finished height together. Leave room to operate the release handle and recliner controls.
Plan your Audi 80 Type 81/85 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Back to the Car Seat Selector guide.
Fitting references: Corbeau subframe and included-runner guidance. Seat specifications and drawings: Classic, Alpine, GT8 and RRS low base. Harness reference: TRS Clubman four-point.





