Alfa Romeo 145 bucket seat guide
A seat change for the three-door Alfa
A 145 still doing the school run needs a different seat arrangement from one being stripped for circuit days. Rear-seat access, the original runners and the width of the new seat all affect the order.
For this Alfa, we list a Sparco vehicle-specific frame. Cameron would start by checking the runners already in the car. Garreth would then choose between a reclining seat for regular use and a fixed-back bucket for a more focused build.

At a glance
- Vehicle: Alfa Romeo 145, Tipo 930. Sparco’s application sheet covers July 1994 to September 2000.
- Listed vehicle frame: Sparco 00499085 family, sold for one seat with a side selection.
- Seat-side base pattern: 345mm across by 271mm front to rear.
- Runners: inspect the original assembly before buying an additional slider.
- Side-mounted shells: need a separate, matched side-mount arrangement above the frame.
The fitting kit for an Alfa 145
The Sparco Alfa Romeo 145 subframe is the starting point. Our listing is part number 00499085, with RHD driver and passenger options. It is sold singly, so a two-seat conversion needs the correct frame for each side.
Its stated 345mm x 271mm pattern is the connection above the vehicle frame. It does not describe the spacing of the holes in the Alfa floor, and it does not establish whether a particular seat clears the door or centre tunnel.
Check the physical left or right side when ordering, particularly if the car is left-hand drive. A manufacturer’s European driver/passenger description can differ from the sides of a UK car.
-
From £87.00 Incl. VATFrom £72.50 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
Start with the runners already in the car
Sparco’s application sheet marks the 145 frame “Serie”. Its key describes original sliding rails underneath the Sparco base for a tuning installation, with a separate competition qualification. That is why we would inspect the existing runners before adding a universal kit.
Cameron would ask for a photograph of the seat base and runners, particularly on a car that has already had its seats changed. Send the proposed seat model too, so the complete arrangement can be checked together.
Our Sparco sliding runner kit is a separate 345mm x 271mm component. It is useful in an assembly designed to accept it, but the matching seat pattern alone does not establish that it should replace or sit alongside the Alfa’s original runners. Garreth would settle that detail before putting a second slider in the order.
For a competition build, send the proposed seat, mount arrangement and the requirements for the intended event. The archived road-use arrangement should not be assumed to cover a competition installation.
The bolt pattern, drawn to scale
The four centres above use the same scale in both directions. The surrounding outline is schematic. The dimensions come from Sparco’s application sheet and agree with our current frame listing.
A base-mounted seat needs the correct fixing pattern through every part of the assembly. A shell with side fixings needs compatible side mounts, whose base must also match the arrangement beneath it.
Bucket seats to start with
The Sprint, Sprint L and TRS-X are fixed-back seats with base and side mounting options in their current listings. Their different driver sizes make them useful starting points for a 145 enquiry. They are a shortlist to measure in the car, not a promise of cockpit clearance.
OMP’s catalogue gives 345mm x 270mm as its Type Y bottom-fixing reference. Have us check the TRS-X mounting drawing against the complete rail and frame arrangement before ordering. The Sprint versions also need their current drawings and fasteners checked for the selected assembly.
-
From £252.00 Incl. VATFrom £210.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
- Sparco Sprint: the current listing gives a 32 to 36 inch waist guide.
- Sparco Sprint L: the current listing gives a 40 to 42 inch waist guide. Allow for the larger seat when measuring the cockpit.
- OMP TRS-X: listed in 28 to 32 and 32 to 36 inch waist ranges. Confirm the version against your measurements.
Waist ranges help narrow the choice. Cameron would also check the seat’s external shoulder width, cushion position and harness-slot height against the driver. If you choose a different side-mounted shell, include its side mounts in that check.
Reclining seats for a regularly used 145
A reclining backrest is useful when the rear seats are still in use. The Sparco R100, R333 and GT all list a 345mm x 271mm base pattern, so they are worth comparing against this frame and the existing runner arrangement.
Choose by the backrest shape, support and ease of entry you want. The R333 and GT listings give a 32 to 36 inch waist guide and an under-six-foot height guide. The R100 has broader listed size guidance, though its outside dimensions and control clearance still need checking in your car.
-
From £282.00 Incl. VATFrom £235.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
-
From £449.47 Incl. VATFrom £374.56 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
£562.10Original price was: £562.10.£505.90Current price is: £505.90. Incl. VAT£468.42Original price was: £468.42.£421.58Current price is: £421.58. Excl. VATPayPal CreditKlarna ReadyAdd to basket
Garreth’s first choice for a road-focused enquiry would be to try a reclining seat before committing to a fixed shell. Cameron would set the seat far enough back to check the backrest controls, door clearance and access behind it.
Harnesses: choose the seat and mounting route together
The R100, R333 and GT listings specify four-point harness compatibility. The bucket-seat shortlist has six-point compatibility listed, with four-point compatibility also stated for the TRS-X. Those entries describe the seat, so the mounting points in the car still need checking separately.
The TRS Clubman clip-in and bolt-in four-point belts offer different end fittings. Both listings say they are not HANS compatible. The Schroth Profi 3×2 is a six-point, HANS-friendly option for a suitable seat and complete installation. It needs the appropriate crotch-strap provision as well as the lap and shoulder mounting arrangement.
-
From £120.00 Incl. VATFrom £100.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £81.00 Incl. VATFrom £67.50 Excl. VATPayPal CreditAmazing valueSpeed+ ServiceSelect options This product has multiple variants. The options may be chosen on the product page
-
From £444.01 Incl. VATFrom £370.01 Excl. VATPayPal CreditKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
Before choosing a belt, send a photograph of the area behind the seats and tell us which seat you plan to use. Follow the harness manufacturer’s installation instructions for the particular belt. A harness bar or cage tube should only be used for mounting where that component’s maker specifies it.
What to measure in your Alfa
- Available width at the seat base, hip bolsters and shoulders, with the door closed.
- Your seated height and headroom in the complete frame, runner and seat assembly.
- Steering-wheel reach and pedal operation at the intended seat position.
- Space for the recliner controls, runner handle and rear-seat access.
Check these measurements with the particular seat drawing. Changing the frame does not establish that the finished seat will sit lower than standard. If two people drive the car, check both driving positions.
Common questions
The Sparco Alfa Romeo 145 direct-fit subframe, part family 00499085. Select the appropriate side. It is sold for one seat.
Check the existing assembly first. Sparco’s application sheet specifies original runners beneath this base for its tuning arrangement. We would confirm the current frame and proposed seat together before adding a separate slider.
A side-mounted shell needs a compatible pair of side mounts above the frame. The side mounts, any runner and the frame must be checked together, along with shell clearance in the car.
A seat on the matching 345mm x 271mm pattern is a mounting candidate. Confirm its actual drawing, the full assembly and cockpit clearance. Sharing a brand name is not a fitment measurement.
Our separate Alfa 146 listing uses the same Sparco part family, but this guide is for the three-door 145. Body access and the particular installation still need checking for a 146.
The car’s year and steering side, photographs of its existing runners, the seat model you are considering and your height and waist measurement. Include whether rear-seat access or competition use is part of the brief.
Garreth’s top tip
Keep the original runners until the full mounting arrangement is settled. For a road car, I would put access and everyday comfort near the top of the seat shortlist.
Cameron’s fitting view
Send a clear photograph of what is under the current seat. I would check that against the frame and the proposed seat before deciding which extra fittings belong in the order.
Plan your 145 seat change
Drop us an email or click to open a chat through our contact page. For a full seat and fitting-kit recommendation, call 0115 647 8650.
Technical reference: Sparco application sheet, pages 14 and 19. This archived sheet supplies the base-pattern and original-runner reference; confirm the current parts for your car when ordering.









