OMP Champ-R: The Perfect Bucket Seats For Your Toyota Chaser
Customer car, December 2025
Finding a motorsport seat that suits the car and the driver is not always easy, so we were pleased with how a pair of OMP Champ-R seats went into one of our customer's Toyota Chasers. They went in without trimming or adjusting, clear of the door cards and the centre console, on a Planted Technology sub-frame and side mounts.
The deep side bolsters and big shoulder supports change the feel of the Chaser's cabin, and the seats look as if they belong there. Here is what the Champ-R is, how it fits the driver and the car, and how this install was put together.
- OMP Champ-R: fibreglass shell, around 8.9kg per seat
- FIA 8855-1999 homologated and HANS friendly
- Five harness slots; our listing gives it as 4 point and 6 point compatible
- Side mount only, with removable lumbar and leg cushions
- Our listing sizes it for a 32 to 36 inch waist and drivers under 6ft
- Fitted on a Planted Technology Toyota Mark II (X100 chassis) seat bracket

What is on this page
Why fit bucket seats to a Chaser
Swapping the factory seats for motorsport buckets is one of the changes you feel most, especially on a car used for track days, drifting or enthusiastic road driving. The Chaser’s original seats were never designed to hold you in place through fast corners or quick changes of direction.
A bucket seat like the Champ-R keeps you in place with deep side and shoulder support. That means less effort spent bracing yourself and more attention on driving the car, which is the whole point on a car like this.
Inside the OMP Champ-R
The Champ-R is built around a gel coated fibreglass shell, which our listings put at around 8.9kg a seat. That is a real saving over a steel framed seat, and a composite shell holds its shape under cornering load. The shell is fairly slim, which helps in a cabin like the Chaser’s.
It is homologated to FIA 8855-1999 and HANS friendly. There are five harness slots, and our listing gives it as compatible with 4 point and 6 point harnesses. Like every FIA seat, the approval runs from its date of manufacture, so we check the dates on the label for any seat going into a competition car.
The lumbar and leg cushions are removable, so you can tune the fit a little and take them out to clean. The side bolsters are medium height, enough to hold you in hard cornering while still letting you climb in and out, which matters on a car that is still driven on the road.
Key features of the Champ-R, from our listings and the install:
- Gel coated fibreglass shell
- FIA 8855-1999 homologated
- HANS friendly
- Five harness slots
- Removable lumbar and leg cushions
- Side mount only

Will the Champ-R fit you?
The Champ-R is a narrow seat, and that is part of why it suits the Chaser. It has worked well in other tight cabins too, such as the Mk1 Mazda MX-5.
| Measurement | OMP Champ-R |
|---|---|
| Shoulder width | 580mm |
| Base width | 520mm |
| Waist (our listing) | 32 to 36 inches |
| Driver height (our listing) | Under 6ft |
| Weight (our listing) | Around 8.9kg |
The shoulder supports are big enough to keep the upper body in place, while the base is slim enough to stay clear of the door trims and the console. Garreth’s advice is to sit in one before you buy if you can. We kept the Champ-R on display in the showroom, so you could try one for size.
The install: Planted Technology X100 brackets
For this Chaser we used the Planted Technology seat bracket listed under the Toyota Mark II on our site. It is made for the X100 chassis, and the Chaser and the Mark II share it. The bracket bolts to the factory mounting points in the floor, so no drilling is needed.
The Champ-R is side mount only, so side mounts bolt to the seat and then to the bracket. On this install they went onto the bracket’s 345mm holes. As the listing says, the bracket is a driver side part; ask us about the passenger side if you want a pair.
If you want to slide the seat, a runner kit goes between the bracket and the side mounts. That suits a road car. For the lowest driving position in a motorsport car, leave the runners out and bolt the side mounts straight to the bracket. An FIA seat also needs approved side mounts: an approved seat on unapproved mounts is not an approved installation.
Other bucket seats for the Chaser
The Champ-R is a good match, but it is not the only seat that suits the Chaser. We carry similar sized buckets from Sparco, Mirco, Cobra and OMP, and a side mount seat on the right side mounts can go on the same Planted bracket. Tell us your measurements and how the car is used, and we will narrow it down.
Our guide to the top bucket seats for the Toyota Chaser goes through the options, and base mount or side mount explains how the bracket, runners and mounts stack up.
Does the OMP Champ-R fit a Toyota Chaser?
Yes. This pair went into our customer’s Chaser on a Planted Technology X100 bracket and side mounts, without trimming.
Is the OMP Champ-R FIA approved?
Yes. It is homologated to FIA 8855-1999, and the approval runs from its date of manufacture.
Is the Champ-R side mount or base mount?
Side mount only. Side mounts bolt to the seat and then to the vehicle bracket.
What size driver does the Champ-R suit?
Our listing sizes it for a 32 to 36 inch waist and drivers under 6ft.
Which bracket fits the Chaser?
We used the Planted Technology bracket for the Toyota Mark II on the X100 chassis, which the Chaser shares.
💬
Our viewA clean fit in the Chaser
The Champ-R on a Planted X100 bracket went in without trimming. Send us your measurements to check it suits you.
Need a personal recommendation?
We're here to ensure you pick the right seat.
Contact us today.



![Planted Technology Toyota Mark II [8th Generation / X 100 Chassis] (1996-2000) - Driver / Right Seat Bracket](https://www.sportseats4u.co.uk/wp-content/uploads/sites/2/2026/08/Planted-ImageUnavailable_6258563e-39b9-4784-8c52-314c93d293a1-300x300.jpg)