Customer Car: Ford Escort Mk1 with Mirco GT 3D Seats
Customer car, September 2025
Classic rally cars always get attention at the showroom, and this Ford Escort Mk1 is one of the best we have seen. The customer has fitted a pair of Mirco GT 3D bucket seats trimmed in 3D spacer fabric, which suit the car's rally setup well. With uprated suspension, a tidy rally interior and pearl white paint, it looks every bit the part.
After fitting the seats, the customer brought the car back to us for photos and told us about the build: its past in road rallies, the Safety Devices roll cage and TRS harnesses, and plans for a more powerful engine. The new seats make the most of the small cockpit while the rest of the car stays true to its rally roots.
- Car: the customer's pearl white Ford Escort Mk1, with a road rally history
- Seats: a pair of Mirco GT 3D FIA bucket seats in 3D spacer fabric
- Harnesses: TRS Magnum 4 point FIA
- Cage: Safety Devices Ford Escort Mk1 Cross 6 point bolt in
- Mounting: Endurance Motorsport steel M8 side mounts on fabricated floor mounts

What is on this page
About the customer's build
When the Escort came back to us we had time to get to know it. It has a genuine rally background, having taken part in road rallies, and it still has the purposeful setup of a car that has done the job. Underneath, the suspension has been uprated for rally stages.
Inside there is a Safety Devices roll cage and TRS harnesses, which bring the restraint up to date while keeping the classic rally look. The cockpit is clean and functional, with every part there for a reason. The customer’s plans include an engine swap for more power, so this is a car that keeps evolving.
The cabin is a proper rally office: a trip meter on the passenger side, a switch panel and fuse board in the centre, the cage tubes running round the edges, and the Mirco seats sitting low with the TRS harness buckles ready.
Every part of it has a job, which is exactly how a car like this should be built.

Why upgrade the seats in an Escort Mk1?
The Mk1 Escort’s reputation as a rally car is secure, but its seats are products of their time. The originals give little side support, so on a stage, a track or a twisty road you slide about and end up bracing against the wheel or the door, which takes your focus off driving.
Comfort and fatigue matter too. Flat period foam was never designed for long competition stages, and constantly shifting in the seat is tiring. A modern FIA bucket seat with a proper harness holds you in place, so all your concentration can go into driving the car. For road rally use, better seating makes a big difference to confidence.
The parts in this build
- Mirco GT 3D bucket seats: fibreglass FIA 8855-1999 seats in breathable 3D spacer fabric, with the side support a road rally car needs in a small cockpit.
- TRS Magnum 4 point FIA harnesses: homologated harnesses for driver and passenger.
- Safety Devices Ford Escort Mk1 Cross 6 point roll cage: a bolt in cage made for the Mk1.
- Endurance Motorsport steel M8 side mounts: used to fix the Mirco seats in the car. There was no vehicle specific frame for this setup, so the customer had floor mounting points fabricated for the side mounts.
-
From £388.80 Incl. VATFrom £324.00 Excl. VATPayPal Credit250+ coloursKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £246.00 Incl. VATFrom £205.00 Excl. VATPayPal CreditAmazing valueSelect options This product has multiple variants. The options may be chosen on the product page
-
From £916.80 Incl. VATFrom £764.00 Excl. VATPayPal CreditMade to orderKlarna ReadySelect options This product has multiple variants. The options may be chosen on the product page
-
From £34.80 Incl. VATFrom £29.00 Excl. VATPayPal CreditSelect options This product has multiple variants. The options may be chosen on the product page
About the Mirco GT 3D
The GT 3D is one of the most versatile motorsport seats we sell. The fibreglass shell is strong and relatively light, and the 3D spacer fabric was the customer’s choice for its breathability on long stages and in hot weather. It is homologated to FIA 8855-1999, so it suits competition as well as road rallies and fast road use.
- Fibreglass shell
- FIA 8855-1999 homologated
- Breathable 3D spacer fabric trim
- High side and shoulder bolsters
- 4 point or 6 point harness compatible, and HANS friendly
- Listed for drivers under 6ft with a 32 to 36 inch waist
Seat dimensions and Escort fitment
Space was the hardest part of this build. The GT 3D is the largest seat we could fit in this Escort, and even then it was a very tight squeeze. With the cage in, the seats sit right up against the door bars, and the customer had to modify the centre tunnel to get them in. Even without door bars we would not go wider than the GT in a Mk1; any wider and you risk clashing with the door cards or the tunnel.
| Mirco GT | Measurement |
|---|---|
| Overall height | 930mm |
| Shoulder width | 590mm |
| Base width, external | 495mm |
| Base width, internal | 380mm |
| Depth | 600mm |
| Weight | approx. 9.5kg |
Fitting seats in an Escort Mk1
Fitting seats in a Mk1 is not easy. The cockpit is small, and this car needed its seat mounting fabricated. The customer came prepared, having measured the interior first, which made choosing the seat much easier.
If your car needs fabricated mounts, we suggest having a specialist do the work, and for a competition car, checking with your scrutineer before the car is built. We supply the side mounts to fit the seat, and an optional sliding runner kit. Runners raise the seat by about 25mm, which may not suit a taller driver in the Escort’s low roof, and we only suggest them for road cars, not competition cars. That is why this customer went without them.
Narrower seats for an easier fit
If you want bucket seats in a Mk1 without modifying the centre tunnel, a narrower steel framed seat is the easier route. They are slimmer than the bigger fibreglass shells, so they go in with far less work while still being FIA homologated. The Sparco Sprint and the Corbeau Club Sport are good places to start.
They give a little less room than the GT 3D, but they fit without major changes. Garreth’s advice for any Mk1 is the same as this customer’s approach: measure the car first, then choose the seat.
Does a Mirco GT 3D fit a Ford Escort Mk1?
It did in this car, but only just. The seats sit against the cage door bars and the centre tunnel needed modifying.
What is the widest seat for an Escort Mk1?
In this build the Mirco GT, at 590mm across the shoulders, was the widest that would go in. We would not go wider.
Is there a direct fit frame for this Escort?
Not for this setup. The customer had floor mounting points fabricated for Endurance side mounts.
Should I use sliding runners in a rally Escort?
We only suggest runners for road cars. They also raise the seat by about 25mm.
Which narrower seats suit an Escort Mk1?
Steel framed FIA seats such as the Sparco Sprint or Corbeau Club Sport fit more easily.
💬
Building a Mk1?Measure first, then talk to us
Send us your cabin measurements and your size, and we will suggest the seat that fits both.
Need a personal recommendation?
We're here to ensure you pick the right seat.
Contact us today.




